Nortek 2GIG GC2 - RF Keypad Programming Outline; Summary of RF Keypad Screen; RF Keypad Programming Questions

Go!ControlWirelessSecuritySystem|InstallationandProgrammingGuide
50Copyright©2016NortekSecurity&Control
RF Keypad Programming Outline
Figure 55 Keypad Programming Outline
Scrollbetweenoponsusingthe←and→arrows.Moveto
thepreviousornextpromptbytappingthe↑and↓
arrows.
1 To programanothersensortapNext.
2 To exitprogramming,tapSkip,thenEnd,andthenExit.
Uponexit,thepaneltakesseveralsecondstorestart.
3 TapSkiptojumptoquestionQ5.
Summary of RF Keypad Screen
Afterset tingalltheoptionsforasensor,theRFkeypad
summaryscreenisdisplaye d.Thescreencanalsobe
displayedforprogrammedRFkeypadsbytappingtheSum
button.
•Toret
urntoprogramming,taptheEditCurrentor
EditNextbuttons.
• TappingSk
ipgoestoquestionQ5(ControlPanel
programming).
•Toexi
tprogramming,tapSkipthenEndandExit.
Uponexit,theControlPaneltakesseveralseconds
torestart.
RF Keypad Programming Questions
Q4: Select RF Keypad # (1 to 4)
Uptofour(4)wirelesskeypadscanbeprogrammedforuse
witheachControlPanel.Theoptionsforeachsensorare
programmedwithsub‐optionquestions:
•Beginbyen
teringtheRFKeypadnumberorselectit
usingthe←or→arrows.
•ProgramtheRFke
ypadsbyusingthe↑and↓
arrowstoselectthesub‐options.
Toski
pRFKeypadprogramming,tapSkiptojumpfrom
questionQ4toquestionQ5(ExitDelayprogramming).
Q: Select RF Keypad (#) Used (0 to 1)
DEFAULT:(0)U
nused
UserscanuseRFkeypadstogetherwithaControlPanelor
not.
•Thedefaultsetting(0)UnusedsetsallRFkeypadsas
unused.
•Toen
ableprogrammingforthisRFkeypad,select
(1)Used.
Q: Select RF Keypad (#) Equipment Code (0-9999)
DEFAULT:(0000)Othe
r
TheRFkeypadequipmentcodedefinesthesensor’s
manufacturerandtype.
•Thedefaultsettingis(0000)Other.
• Select(
0867)2GIGWirelessKeypad.
• Select(10
59)2GIGTS1WirelessTouchscreen
Keypad.
NOTE: Th
e2GIGWirelessTouc hScreenKeypadisnot
intendedforUL985:HouseholdBurglar‐AlarmSystem
Unitsinstallations.
Q: Enter RF Keypad # Other Equipment Code (0-9999)
DEFAULT:0
NOTE: Th
isquestionisonlydisplayedif(0000)Otheris
selectedastheRFkeypad’sequipmentcode.
IMPORTANT: Thee
quipmentcodeisafour(4)‐digitcode
thatisassignedtotheappropriatekeypadmodelbeing
used.
•Enterthee
quipmentcodenumberfortheRF
Keypad.
Q: Enter RF Keypad# Serial Number (7 Digits)
DEFAULT:0000000
or
RFKeypad(#)KeypadID(read‐only)
Serialnumbersforstandardwirelesskeypadscanbe
manuallyenteredorlearnedfromthekeypad.ForWireless
TouchScreenKeypads,serialnumberscanonlybelearned
fromthekeypad.Read‐onlywithKeypadID’srefertothe
installerbeingunabletomanuallyinputanid.
Sta
ndardKeypads
:
•Formanualentry,entertheWirelessKeypadthat
wasloggedforthekeypadbeingprogrammed.Tap
theShiftbuttontoaccessalphacharacters.
•Foraut
omaticentry,tapShiftandthenLearn.This
placestheControlPanelintolearningmode.When
youtriggerthekeypadthesensorforthekeypad
beingprogrammed,itsendsitsserialnumbertothe
ControlPanel.