Nortek 2GIG GC2 - Page 45

Installer Programming
Copyright © 2016 Nortek Security & Control 43
Q: Select RF Sensor # Equipment Type
DEFAULT:Va
riesbyRFSensorType
NOTE: Somesensortypes(zones)willrequireyoutospecify
anequipmenttypeselection,whichaffectsthesensor’s
extendedreportingcode.
Simplyentertheappropriateequipmenttypecode(see
tablebelow)ortapthe←or→arrowstoselectthe
appropriateequipmenttype.
ThetablebelowshowstheEquipmentTypesavailablefor
eachSensorType(Zone):
Q: Select RF Sensor # Equipment Code
DEFAULT:(0000)Oth
er
Selectthefour(4)‐digitequipmentcodethatcorresponds
totheappropriatesensormodel.See"EquipmentCodes"on
page40.
Q: Select RF Sensor # Other Equipment Code
NOTE: Thissu
b‐questionisonlydisplayedif(0000)Otheris
selectedastheRFSensor#EquipmentCode.
Entertheeq
uipmentcodenumberdirectlyonthekeypad
fortheRFsensor.Enter“0”ifthenewequipmentcodeis
unknown.
Q: Enter RF Sensor # Serial Number (7 Digits)
DEFAULT:0000000
RFse
nsorserialnumberscanbemanuallyenteredor
automaticallytransmittedfromthesensortotheControl
Panel.
• Fo
rmanualentry.Enterthesensornumberthat
waslog gedforthesensorbeingprogrammed.Tap
Shifttoaccessalphabeticcharacters.
• Fo
rautomaticentry.TapShift,thentapLearnto
placetheControlPanelintolearningmode.Then
triggertheRFsensor.TheControlPanelwillbeep
four(4)timesandlearnthesensor’sserialnumber.
Ifthese
nsorbeinglearnedisalreadyinmemory,the
ControlPanelwilldisplayasensorlearningfailurescreen
whentheprogrammingchange sarebeingsaved.
Forcertainsensorswithmorethantwoloops,thetamper
switchmustbeusedtosendasignaltotheControlPanel
duringsensorlearning.Thefir
stpressofthetamperswitch
willlearnthesensorintothepanelasLoop#1.Thesecond
pressofthetamperswitchwilllearnthesensorintothe
panelasLoop#2,andthethirdpressofthetamperswitch
willlearnthesensorintothepanelasLoop#3.Pa
use15
secondsbetweeneachpressofthetamperswitch.
TheprogrammedloopnumberofthesensorintheControl
Panelmayneedchangingtosuittheoperationofthe
device.Fordetails,seetheInstallationInstructionsincluded
withthesensor.
Q: Select RF Sensor # Equipment Age (0 to 1)
DEFAULT:(0)New
TheCon
trolPanelcanbeusedwithneworexistingRF
sensors.
•IfthisRFsensorisnewfortheinstallation,leavethe
defaultsettingof(0)New.
•Ifthi
sRFsensorisalreadyinstalled,select(1)
Existing.
NOTE: IftheRFsen
sorhasmorethanoneloopandisbeing
programmedintomultiplesensornumberstosupport
theloops,setonlyoneloopas“new”andtheother
loopsas“existing” .Thiswillpreventincorrectin ventory
oftheinstalledsensors.
Q: Select RF Sensor # Loop Number (1 to 3)
DEFAULT:Va
rieswithsensormodelselected
The2GIGDoor/WindowContactsensorshavetwo(2)
inputs:aninternalmagneticcontactandanexternal
NormallyClosed(N/C)hardwiredinput.Eitherorboth
sensorinputscanbeused.
TIP: Somesensorsarecapableofthree(3)loopinputs.
NOTE: Whe
nusingboththeinternalmagneticcontactand
theexternalinput,themagnetcontactANDthe
externalcontactmustbeassignedadifferentRFsensor
number.Bothsensornumberswillsharethesame
sensorserialnumber.
•Whenprogrammingthesensortousethebuilt‐in
magneticcontact,settheloopnumberto(2)2.
•Whenpr
ogrammingthesensortouseitshardwired
input,settheloopnumberas(1)1.
•Whenpr
ogrammingathree(3)‐loopsensortouse
anadditionalinput,settheloopnumberas(3)3.
•Whenen
teringthesensornumberforthesensor’s
loop2or3,tapPastetorecallthelastprogrammed
sensor’sserialnumber.(Thesensornumberwillbe
filledinautomaticallyifLearnisused.)
Q: Select RF Sensor # Dialer Delay (0 to 1)
DEFAULT:(1)Enabled
Ifthisfeatureisenabled,thedelaytimemustbesettoa
minimumof30secondsforANSI/SIAcompliance.Tosetthe
(02)Exit/Entry2 Y Y
(03)Perimeter YY
(04)InteriorFollower* Y Y
(05)DayZone YY
(06)24‐HourSi lentAlarm* Y Y
(07)24‐HourAudibleAlarm* YY
(08)24‐HourAuxi liaryAlarm* Y Y
(09)24‐HourFire YN
(10)InteriorwithDelay* Y Y
(14)24‐HourCarbonMonoxide YN
(16)24‐HourFireVerification Y N
(23)NoResponseType* YY
(24)SilentBurglary Y Y
SensorType(Zone) EquipmentTypes
(04)InteriorFollower (1)Motion
(2)Contact
(06)24‐HourSi lentAlarm (1)Contact
(11)Emergency
(07)24‐hourAudibleAlarm (1)Contact
(11)Emergency
(08)24‐HourAuxi liary (1)Contact
(6)Freeze
(8)Water
(10)Temperatu re
(11)Emergency
(10)InteriorwithDelay (1)Motion
(2)Contact
(23)NoResponseType (1)Contact
(2)Motion
SensorTypes(Zone) RF Wired