OERTLI OS 4 - Core PCB

151 pages

Save Page as PDF

To Next Page

To Previous Page

2021-03-23 / Rev. 10 VV016042 44

10.2 Core PCB

Main Page

Table of Contents3
About this Document6
Warnings and Symbols in this Manual6
Warnings and Symbols on the Unit6
Safety Instructions7
Abbreviations and Terms7
Device Overview / Versions7
General Overview7
Anterior Posterior Segment Version VC86020X8
Anterior Posterior Segment Version with Endo Laser Function VC86030X8
Block Diagram OS48
Installation9
General Remarks9
Power Supply9
Infusion Pole10
Door Remote Switch (DRS) for Endo Laser Module10
Service Mode Operation11
Login and Main Menu11
Configuration of the Unit12
Pedal Status16
Sensor Calibration17
Pedal Calibration17
Check - Logging18
OS 4 Service Tools18
Conversion of the Surgeon Memory18
Procedure for Converting a Database from a Device with SW Version 1.5.X19
Procedure for Converting a Database from a Device with SW Version 1.4.019
Procedure for Converting a Database from a Device with SW Version 1.3.020
Trouble Shooting22
Loading of Calibration Values of Spare Parts23
Installation of the Driver Software23
Loading of Adjustment Values with the Service Tool25
Endo Laser System Calibration28
Laser Safety28
General Servicing Procedure29
Maintenance Schedule29
Inspection and Cleaning of Test Fibre29
Laser Servicing Software30
Introduction30
Installation31
Overview of Laser Service and Maintenance32
Calibration Procedure33
Preparation for Calibration33
Fibre Check37
Short Calibration Guideline - Power Laser PLD (Working Beam)38
Short Calibration Guideline - Target Laser TLD (Aiming Beam)40
Remote Servicing - Second Level Support43
Device Composition43
PCB Overview43
Unit43
Pedal43
Core PCB44
Power PCB46
Supply PCB47
Carrier Print48
Fluidic PCB50
Control Panel PCB51
Power) LED Module PCB51
Power) Ledplus Module PCB52
Air Sensor PCB53
Visco Sensor PCB53
Vit Pn Sensor PCB53
Wireless Module53
Fluidic Sensor PCB54
Pedal PCB54
Power Supplies55
Isolation Transformer55
Power Supply 24 VDC56
Power Supply 12 VDC56
Installing and Uninstalling of Device Components57
General57
Fuses57
Hook for Infusion Pole57
Front Castor Wheel58
Back Castor Wheel58
Housing60
Front Enclosure62
Power Supply 24 VDC64
Power Supply 12 VDC65
Varistor / Isolation Transformer Assembly65
Drive for Infusion Pole66
System Unit68
Supply PCB70
Wireless Module70
Carrier Print71
Holder for Gas Forced Infusion (GFI)73
Control Panel73
Phaco Connector77
DIA Connector78
Fluidics Unit78
GFI Module84
AIR Module87
Visco Module89
Vit-PN Module92
Source Pressure Module94
Components of Posterior Version95
Power Ledplus Module95
Power LED Module96
Components of Laser Version97
Spare Key for Endo Laser97
Laser - DRS Dongle97
Protection Cap for Laser97
Fibre Coupling Unit for Endo Laser98
Endo Laser Module99
Exchange of Connecting Cable Laser to UPF Connector101
Software Update103
Update Order103
General Updating Procedure104
Versions105
Version 2.0.0105
Versions 1.5.X105
Version 1.4.0106
Version 1.3.0106
Version 1.2.0106
Version 1.1.0107
Installing and Uninstalling of Pedal Components108
Pedal Housing108
Pedal Housing up to Serial No. 80670098108
Pedal Housing from Serial No. 80670099109
Sealing Set110
Rechargeable Battery112
Pedal PCB113
Connecting Rod114
Sensors116
Horizontal Pedal Sensor116
Vertical Pedal Sensor118
Rubber Mat120
Protection Sheet120
Pedal Handle121
Side Switches Left or Right122
Wireless Module123
Cable for Pedal123
Messages, Warnings and Error Messages / Fault Correction124
Information and Warnings124
Error Messages126
Authorized Service Points129
Sending Defective Device, Instrument or Part to Oertli129
Appendix A) Recommended Service Tools for Laser130
Appendix B) Spare Parts132
Spare Parts for the Unit132
Spare Parts for Pedal133
Set of Replacement Screws133
Set of Small Replacement Parts133
Appendix C) Safety Check134
Appendix D) Functional Test136
Appendix E) Laser Installation Protocol147

OERTLI OS 4 - Core PCB

Table of Contents