To Next PageTo Next PageWhy is there no sound coming from my Onkyo NC-500?
If you're not getting any sound, first make sure the speakers are correctly connected and that the speaker cables' core wires are touching the speaker connectors. Also, check that the volume level isn't set to the minimum. Finally, if the MUTNG indicator is flashing, cancel the muting function.
Why will my Onkyo Receiver not turn on?
If the system isn't powering on, ensure the power cable is properly plugged into the AC outlet. If it is, unplug the power cable from the AC outlet, wait for at least five seconds, and then plug it back in.
What to do if the Onkyo NC-500 remote controller does not function correctly?
If the remote controller isn't working, first ensure the batteries are installed with the correct polarity (+/–). If that doesn't work, try replacing both batteries with new ones, making sure not to mix different types or new and old batteries. Also ensure you are using the same REMOTE ID code.
General| Audio formats | MP3, WMA, AAC, WAV, FLAC, ALAC |
|---|---|
| Network | Ethernet, Wi-Fi |
| Streaming services | Spotify, TIDAL, Deezer, TuneIn |
| Amplifier power | 30 W + 30 W (4 Ohms, 1 kHz, 0.7% THD, 2 Channels Driven, IEC) |
| Power Output | 30 W + 30 W (4 Ohms, 1 kHz, 0.7% THD, 2 Channels Driven, IEC) |
| Frequency response | 10 Hz–100 kHz/+1 dB, -3 dB (Direct Mode) |
| Frequency Response (Direct Mode) | 10 Hz–100 kHz/+1 dB, -3 dB |
| Inputs | USB, Analog, Optical |
| Outputs | Speaker terminals, Headphone |
| Audio Decoders | Dolby Atmos, DTS:X |
General guidelines for safe operation and retention of instructions.
Covers cleaning, attachments, environment, placement, and ventilation.
Details power sources, grounding, polarization, and cord protection.
Guidelines for grounding antennas and protecting against lightning surges.
Addresses proximity to power lines, overloading, and preventing object/liquid entry.
Procedures for servicing and conditions requiring professional repair.
Explains the NC-500's role as a network audio client for music streaming.
Details all ports and connectors on the rear of the NC-500 unit.
Guide on how to properly connect speakers to the NC-500, including impedance and wire preparation.
Requirements and steps for connecting the NC-500 to a LAN for Internet and server access.
Overview of Net-Tune Central features and PC system requirements.
Guide through the initial steps of the Net-Tune Central setup wizard.
Steps to confirm the installation and finish the setup process.
How to set the NC-500 input source to "Server" and connect to the music library.
Guide on how to store and assign preset numbers to radio stations.
Steps to set up the alarm feature, including source and time.
Detailed procedure for setting the specific time for the alarm to activate.
How to choose the audio source (server, radio) for the alarm.
Introduction to Internet radio and ensuring network connectivity.
Steps to save favorite Internet radio stations in memory.
Explains the importance of configuring network settings for LAN and Internet access.
Steps to access and configure Ethernet settings on the NC-500.
Details on how to manually set the IP address and subnet mask for the NC-500.
Instructions for configuring gateway and DNS server addresses for network connectivity.
Detailed steps for entering DNS server addresses.
How to choose the PC that will act as the Net-Tune server on the LAN.
Solutions for problems related to power not turning on or no sound from speakers.
Troubleshooting steps for static, noise, or poor reception during radio broadcasts.
Solutions for issues where the remote controller is not functioning correctly.
Solutions for issues activating Internet radio or music server features.
Troubleshooting for intermittent sound, network load, and inability to obtain Internet radio station lists.
Solutions for failed server connections or music playback issues.
Explains various error messages related to Server input and their meanings.
Explains error messages for Internet Radio and Server/Playback Denied.
