Pacific Power Source ADF Series - Page 6

ADF SERIES™ OPERATION MANUAL
CONTENTS
Entire Contents Copyright  2018 by Pacific Power Source, Inc. (PPS) • All Rights Reserved • No reproduction without written authorization from PPS.
ADF Series Power Source Operation Manual Page 6 of 349
7.3.11 12 DC Power Supply ......................................................................................................................................................... 157
7.3.12 RS232 Description ............................................................................................................................................................ 157
7.3.13 Front Panel Operation of AUX I/O Functions .................................................................................................................. 158
7.4 System Interface Bus Connectors ............................................................................................................... 165
8 Remote Control Programming ...................................................................................................... 166
8.1 Overview ...................................................................................................................................................... 166
8.1.1 Programming Conventions and Notations ..................................................................................................................... 166
8.1.2 Command Terminators .................................................................................................................................................... 167
8.2 Remote Control Command Descriptions by Subsystem ........................................................................... 168
8.3 Calibration Commands ................................................................................................................................ 169
8.3.1 ADF Calibration Commands ............................................................................................................................................. 169
8.3.2 UPC Specific commands. .................................................................................................................................................. 171
8.3.3 AUX I/O Interface Calibration Commands ...................................................................................................................... 171
8.4 Measurement Commands .......................................................................................................................... 172
8.4.1 Voltage Measurement Commands ................................................................................................................................. 172
8.4.2 Frequency Measurement Commands ............................................................................................................................ 173
8.4.3 Current Measurement Commands ................................................................................................................................. 173
8.4.4 Power Measurement Commands ................................................................................................................................... 174
8.4.5 Other Measurement Commands .................................................................................................................................... 174
8.4.6 Measurement Data Logging Commands ........................................................................................................................ 175
8.5 Output Control Commands ........................................................................................................................ 179
8.6 Program Commands ................................................................................................................................... 183
8.6.1 Program Control Commands ........................................................................................................................................... 183
8.6.2 Execution Commands ...................................................................................................................................................... 191
8.6.3 Memory Management Commands ................................................................................................................................ 192
8.7 Source Commands ...................................................................................................................................... 195
8.7.1 Source Configuration Programming Commands ............................................................................................................ 195
8.7.2 Voltage Programming Commands .................................................................................................................................. 199
8.7.3 Frequency Programming Commands ............................................................................................................................. 206
8.7.4 Current Programming Commands .................................................................................................................................. 207
8.7.5 Phase Programming Commands ..................................................................................................................................... 210
8.7.6 Voltage Protection Programming Commands ................................................................................................................ 211
8.7.7 Current Protection Programming Commands ................................................................................................................ 213
8.7.8 Power Protection Programming Commands .................................................................................................................. 215
8.8 Status Commands ....................................................................................................................................... 217
8.9 System Commands ...................................................................................................................................... 219
8.9.1 System Error Commands ................................................................................................................................................. 219
8.9.2 System Information Commands ...................................................................................................................................... 220
8.9.3 System Interface Soft Key Preset Commands ................................................................................................................. 223
8.9.4 System Configuration Commands ................................................................................................................................... 227
8.9.5 Parallel System Commands ............................................................................................................................................. 229
8.9.6 System Sanitization Commands ...................................................................................................................................... 230
8.9.7 Communication LAN Commands .................................................................................................................................... 230
8.9.8 Communication Serial Port Commands .......................................................................................................................... 234
8.9.9 Communication USB Commands .................................................................................................................................... 235
8.9.10 Communication GPIB Commands ................................................................................................................................... 237
8.9.11 System Firmware Commands .......................................................................................................................................... 238
8.9.12 System Remote Access Commands ................................................................................................................................ 239
8.9.13 Miscellaneous System Commands .................................................................................................................................. 240
8.10 Auxiliary I/O System Commands ................................................................................................................ 241
8.10.1 System Analog & Digital IO Commands .......................................................................................................................... 241
8.10.2 SOURce:SYNChronize Commands ................................................................................................................................... 254
8.10.3 PROGram:TRANsient Triggers Commands ..................................................................................................................... 257
8.10.4 AUX I/O Calibration Commands ...................................................................................................................................... 259
8.11 IEEE488.2 Common Commands ................................................................................................................. 263