Pacific Power Source ADF Series - Page 5

ADF SERIES™ OPERATION MANUAL
CONTENTS
Entire Contents Copyright  2018 by Pacific Power Source, Inc. (PPS) • All Rights Reserved • No reproduction without written authorization from PPS.
ADF Series Power Source Operation Manual Page 5 of 349
6.4.2 PROGRAM Output Parameters ......................................................................................................................................... 88
6.4.3 Phase Rotation / Phase Sequence ..................................................................................................................................... 89
6.4.4 Direct Data Entry - Presets ................................................................................................................................................. 90
6.4.5 Customizing Output Programming Preset Soft Key Values ............................................................................................. 91
6.4.6 Changing Shuttle Programming Resolution ...................................................................................................................... 91
6.4.7 PROGRAM & MEASUREMENTS Soft Keys......................................................................................................................... 92
6.4.8 Peak Current Protection Minimum Setting....................................................................................................................... 94
6.4.9 Sine Waveform ................................................................................................................................................................... 95
6.4.10 AUTO RMS Function – Steady State .................................................................................................................................. 96
6.4.11 Option V - Extended AC Voltage Range Operation........................................................................................................... 97
6.5 MEAS – MEASUREMENTS Screens ............................................................................................................. 100
6.5.1 Measurements Screen by Phase ..................................................................................................................................... 100
6.5.2 Three Phase Measurement Screen Soft Keys ................................................................................................................. 101
6.5.3 Individual Phase Measurement Screen Soft Keys .......................................................................................................... 103
6.6 TRAN- TRANSIENTS Screens ....................................................................................................................... 104
6.7 CONF – CONFIGURATION Screens ............................................................................................................. 105
6.7.1 UNIT CONFIGURATION Screens ...................................................................................................................................... 107
6.7.2 USER LIMITS SETTINGS Screen ........................................................................................................................................ 110
6.7.3 RAMP TIME & SLEW RATE SETTINGS Screen .................................................................................................................. 111
6.7.4 PROGRAM MEMORY Screen ........................................................................................................................................... 113
6.7.5 CSC CONFIGURATION Screen .......................................................................................................................................... 114
6.7.6 USER PRESETS Screen....................................................................................................................................................... 115
6.8 SYST – SYSTEM Screens ............................................................................................................................... 117
6.8.1 SYSTEM MENU 1 .............................................................................................................................................................. 118
6.8.2 SYSTEM MENU 2 .............................................................................................................................................................. 118
6.8.3 ERROR / EVENT QUEUE Screen ....................................................................................................................................... 119
6.8.4 FAULT INFORMATION Screen .......................................................................................................................................... 119
6.8.5 INTERFACE Screen ............................................................................................................................................................ 120
6.8.6 UNIT INFORMATION Screen ............................................................................................................................................ 130
6.8.7 PARALLEL UNITS Screen ................................................................................................................................................... 131
6.8.8 SYSTEM SETTINGS Screen ................................................................................................................................................ 132
6.8.9 EXTERNAL STORAGE MANAGEMENT Screen ................................................................................................................. 133
6.8.10 CALIBRATION MENU Screen ............................................................................................................................................ 134
6.8.11 FIRMWARE UPDATE Screen ............................................................................................................................................ 135
6.8.12 REMOTE SUPPORT Screen ............................................................................................................................................... 136
7 Rear Panel, Connectors and Protection ........................................................................................ 137
7.1 OUTPUT Terminals ...................................................................................................................................... 137
7.1.1 Output Power Connector Rating and Isolation ............................................................................................................... 137
7.1.2 Wire Size ........................................................................................................................................................................... 138
7.1.3 Connecting a UUT ............................................................................................................................................................. 138
7.2 External Voltage Sense Input Terminals .................................................................................................... 139
7.2.1 External Voltage Sense Connector Rating and Isolation ................................................................................................ 140
7.2.2 Load Connection without External Voltage Sense ......................................................................................................... 140
7.2.3 Load Connection with External Voltage Sense. .............................................................................................................. 140
7.3 Auxiliary I/O ................................................................................................................................................. 141
7.3.1 Auxiliary I/O Functions ..................................................................................................................................................... 141
7.3.2 DB25 Connector AUX I/O Pin locations ........................................................................................................................... 142
7.3.3 I/O Signal Table by pin number ....................................................................................................................................... 143
7.3.4 I/O Signal Table by Function ............................................................................................................................................ 144
7.3.5 Dedicated Function Digital Inputs ................................................................................................................................... 145
7.3.6 Transient Trigger Input ..................................................................................................................................................... 146
7.3.7 External or Line Sync Input............................................................................................................................................... 147
7.3.8 Digital Output control signals........................................................................................................................................... 150
7.3.9 User Programmable Digital signals .................................................................................................................................. 153
7.3.10 Analog I/O Descriptions ................................................................................................................................................... 155