Panasonic MINAS A5 Series - Page 55

2-7
1
Before Using the Products
2
Preparation
3
Connection
4
Setup
5
Adjustment
6
When in Trouble
7
Supplement
Noise Filter
Option part No.
9ROWDJHVSHFLÀFDWLRQV
for driver
Manufacturer’s
part No.
Applicable
driver (frame)
Manufacturer
DV0P4170 Single phase 100V/200V SUP-EK5-ER-6 A, B-frame
Okaya Electric Ind.
DV0PM20042
3-phase 200V
3SUP-HU10-ER-6
A, B-frame
Single phase 100V/200V
3-phase 200V
C-frame
DV0P4220 Single/ 3-phase 200V 3SUP-HU30-ER-6 D-frame
DV0PM20043 3-phase 200V 3SUP-HU50-ER-6 E-frame
DV0P3410 3-phase 200V
3SUP-HL50-ER-6B F-frame
Remarks
5HFRPPHQGHGFRPSRQHQWV
Model No.
9ROWDJHVSHFLÀFDWLRQV
for driver
Rated
current
Applicable driver
(frame)
Manufacturer
RTHN-5010
3-phase 200V
10 A, B, C-frame
TDK-Lambda Corp.RTHN-5030 30 D-frame
RTHN-5050 50 E, F-frame
FS5559-60-34 60 G-frame
Schaffner
FS5559-80-34 80 H-frame
FN258L-16-07
3-phase 400V
16 D, E-frame
FN258L-30-07 30 F-frame
FN258-42-07 42
G, H-frame
FN258-42-33 42
6HOHFWDQRLVHÀOWHUZKRVHFDSDFLW\LVFRPPHQVXUDWHZLWKWKHSRZHUVRXUFHFDSDFLW\LQ
consideration of the load condition).

)RUWKHGHWDLOHGVSHFLÀFDWLRQVRIHDFKQRLVHÀOWHUFRQWDFWWKHPDQXIDFWXUHU
:KHQWZRRUPRUHVHUYRGULYHUVDUHXVHGZLWKDVLQJOHQRLVHÀOWHUDWWKHFRPPRQSRZ-
HUVRXUFHFRQVXOWZLWKWKHQRLVHÀOWHUPDQXIDFWXUHU

Do not run the input and output wiring on the same passage: noise resistance will drop. (Figure
at lower right)
 Isolate the input and output line from each other. (Figure at lower left)

1
Isolate the input and output
2
3
4
5
6
E
Noise Filter
AC input AC output
Ground
1
The effect of the noise filter is a little.
Do not place the input and output lines
in the same duct or do not tie both in a bundle.
2
3
4
5
6
E
Noise Filter
AC input
AC output
Ground
Surge Absorber
Remarks
Option part No.
9ROWDJHVSHFLÀFDWLRQV
for driver
Manufacturer’s
part No.
Manufacturer
DV0P1450 3-phase 200V R
･
A
･
V-781BXZ-4
Okaya Electric Ind.DV0P4190 Single phase 100V/200V R
･
A
･
V-781BWZ-4
DV0PM20050 3-phase 400V R
･
A
･
V-801BXZ-4
When performing withstand voltage test of machine and equipment, be sure to remove the
surge absorber; otherwise, it will be damaged.
1. Conformance to international standards
&RPSRVLWLRQRI3HULSKHUDO(TXLSPHQWV
Related page
3´'ULYHUDQG/LVWRI$SSOLFDEOH3HULSKHUDO(TXLSPHQWVµ3´2SWLRQµ
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com