Panasonic MINAS A5 Series - Page 77

2-29
1
Before Using the Products
2
Preparation
3
Connection
4
Setup
5
Adjustment
6
When in Trouble
7
Supplement
: High voltage
PC(to be supplied by customer)
Setup support software
“PANATERM”
Please download
from our web site.
0RQLWRURXWSXW
:LULQJWR&RQQHFWRU; P.2-60
Motor cable (Shield wire)
P.2-30
&RQQHFWLRQWRPRWRUGULYLQJ
SKDVHDQGJURXQG
U -phase
V -phase
W -phase
Ground
(earth)
Junction cable
for encoder
Brake cable
DC Power supply
for brake DC24V
(to be supplied
by customer)
Ground terminal
X1
X2
X3
X4
X5
X6
CHARGE
L1
L2 L3
B1 B2
NC
L1C L2C
DB1 DB2
UVW
;WR;DUHXVHGIRUWKHVHFRQGDU\FLUFXLW
To connect these terminals to the primary
power supply (particularly, the 24 VDC
power supply for brake and the 24 VDC
power supply for regenerative resistor),
insulation is required.
Do not connect these terminals to the same
power supply.
3LQ%DQG%
:KHQ\RXFRQQHFWDQH[WHUQDOUHJHQHUDWLYH
resistor, connect the external regenerative
resistor between B1 and B2, set up Pr0.16
to 1 or 2.
3LQ'%DQG'%
:KHQLQVWDOOLQJDQH[WHUQDOG\QDPLFEUDNH
resistor, connect the magnetic contactor (for
controlling) for external dynamic brake to
between LIC and DB1.
7KHYROWDJHDSSOLHGDFURVV'%DQG
'%PXVWEH9$&RUEHORZRU
9'&RUEHORZ
3LQ1&
'RQRWFRQQHFWDQ\WKLQJ
&RQQHFWLRQWR3&3$1$7(50
&RQQHFWLRQWR5656
or host controller
&RQQHFWLRQWR6DIHW\E\SDVVSOXJ
&RQQHFWLRQWRencoder
&RQQHFWLRQWRfeedback scale
&RQQHFWLRQWRKRVWFRQWUROOHU
:LULQJWR&RQQHFWRU; P. 2- 5 7
:LULQJWR&RQQHFWRU; P. 2- 5 5
:LULQJWR&RQQHFWRU; P.2-54
:LULQJWR&RQQHFWRU; P.2-53
:LULQJWR&RQQHFWRU; P.2-51
:LULQJWR&RQQHFWRU; P. 2- 5 1
5HPDUNV
5HPDUNV
2. 6\VWHP&RQÀJXUDWLRQDQG:LULQJ
Overall Wiring (H-frame, 200 V type)
Note
Related page
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
• The figure above shows connections on velocity, position, torque and full-closed mode driver.
• Only for position control type is not provided.
• P.2-30 "Wiring of the Main Circuit (H-frame, 200 V type)"
• P.2-48 "Specifications of Motor connector"