Pentair AK110 - PROGRAMMING SCREEN NAVIGATION: ORP CYCLE TIME (3 of 2)

68
AK110 Programming Screen Navigation, ORP Cycle Time (2 of 2)
Setpoint Overfeed Screen Use the keypad to enter the daily maximum accumulated feed time. Press the [Enter] key to confirm or the down arrow key to cancel. Overfeed Screen
Enter new value Current: 03:00:00 03:00:00 v-Cancel ^
Enter Enter
ORP Cycle, Setpoint Overfeed ORP Cycle, Overfeed
Use the keypad to enter the runtime allowed to reach 5% of setpoint. Disables relay if setpoint is not met. Press the [Enter] key to confirm or the down arrow key to cancel.
Enter new value Current: 00:00:00 00:00:00 v-Cancel ^
From ORP Cycle Time (1 of 2)
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-YES Off if Sw2 On –NO SetOvrfeed 00:00:00< Overfeed 03:00:00 ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-YES Off if Sw2 On –NO SetOvrfeed 00:00:00 Overfeed 03:00:00<
ORP Cycle, Independent of SW2
Enter
ORP Cycle, Feed Off if SW2 is On Press the [Enter] key to make the sanitizer feed dependent or independent of the status of switch 2 (SW2.)
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-YES Off if Sw2 On –NO < SetOvrfeed 00:00:00 Overfeed 03:00:00
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-YES Off if Sw2 On –YES < SetOvrfeed 00:00:00 Overfeed 03:00:00
ORP Cycle , Feed Off if SW1 is Off
Enter
ORP Cycle, Independent of SW1 Press the [Enter] key to make the sanitizer feed dependent or independent of the status of the flow switch SW1.
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-YES < Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-NO < Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00
Use the keypad to enter the cycle duration, including both sanitizer feed ON time and feed OFF time. Press the [Enter] key to confirm or the down arrow key to cancel. Cycle Time Screen
Enter new value Current: 00:02:00 00:02:00 v-Cancel ^
Use the keypad to enter the maximum sanitizer feed duration. Press the [Enter] key to confirm or the down arrow key to cancel. On Limit Screen
Enter new value Current: 00:00:30 00:00:30 v-Cancel ^
Enter Enter
ORP Cycle, Cycle Time ORP Cycle, On Limit
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00< On Limit 00:00:30 Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00 ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30< Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00
AK110 Programming Screen Navigation, ORP Cycle Time, Rev 3 22 Aug 2008