Pentair AK110 - Page 69

69
AK110 Programming Screen Navigation, ORP Cycle Time (2 of 2)
Setpoint Overfeed Screen Use the keypad to enter the daily maximum accumulated feed time. Press the [Enter] key to confirm or the down arrow key to cancel. Overfeed Screen
Enter new value Current: 03:00:00 03:00:00 v-Cancel ^
Enter Enter
ORP Cycle, Setpoint Overfeed ORP Cycle, Overfeed
Use the keypad to enter the runtime allowed to reach 5% of setpoint. Disables relay if setpoint is not met. Press the [Enter] key to confirm or the down arrow key to cancel.
Enter new value Current: 00:00:00 00:00:00 v-Cancel ^
From ORP Cycle Time (1 of 2)
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-YES Off if Sw2 On –NO SetOvrfeed 00:00:00< Overfeed 03:00:00 ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-YES Off if Sw2 On –NO SetOvrfeed 00:00:00 Overfeed 03:00:00<
ORP Cycle, Independent of SW2
Enter
ORP Cycle, Feed Off if SW2 is On Press the [Enter] key to make the sanitizer feed dependent or independent of the status of switch 2 (SW2.)
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-YES Off if Sw2 On –NO < SetOvrfeed 00:00:00 Overfeed 03:00:00
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-YES Off if Sw2 On –YES < SetOvrfeed 00:00:00 Overfeed 03:00:00
ORP Cycle , Feed Off if SW1 is Off
Enter
ORP Cycle, Independent of SW1 Press the [Enter] key to make the sanitizer feed dependent or independent of the status of the flow switch SW1.
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-YES < Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30 Off if Sw1 Off-NO < Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00
Use the keypad to enter the cycle duration, including both sanitizer feed ON time and feed OFF time. Press the [Enter] key to confirm or the down arrow key to cancel. Cycle Time Screen
Enter new value Current: 00:02:00 00:02:00 v-Cancel ^
Use the keypad to enter the maximum sanitizer feed duration. Press the [Enter] key to confirm or the down arrow key to cancel. On Limit Screen
Enter new value Current: 00:00:30 00:00:30 v-Cancel ^
Enter Enter
ORP Cycle, Cycle Time ORP Cycle, On Limit
ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00< On Limit 00:00:30 Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00 ManualTime 00:02:00 Proportional% 5 On If ORP< 700 Off If pH> 7.95 Off If pH< 0.00 Off if RLY On 1 Cycle Time 00:02:00 On Limit 00:00:30< Off if Sw1 Off-YES Off if Sw2 On -NO SetOvrfeed 00:00:00 Overfeed 03:00:00
AK110 Programming Screen Navigation, ORP Cycle Time, Rev 3 22 Aug 2008