Pentair AK110 - PROGRAMMING SCREEN NAVIGATION: HEATER (2 of 2)

85
pH > 7.67-OFF 7.50s
ORP 490 -OFF 700s Heater 68.-OFF 77.0s SW1OFFSW2OFF
Main Status Screen
Name:Main Pool System >Programming
Service Data ( 8:441 ) Communications Security Setup Wizards Serial # 123456
Configuration Menu, Programming
AK110 Programming Screen Navigation, Heater
EnterBack
1:pH, Mix Time 2:ORP, Mix Time >3:Heater
A:Alarm P:Pager1 P:Pager2 P:Pager3 P:Pager4
Programming Setup Screen Heater, Manual Cycle Time
EnterBack
Enter new value Current: 00:02:00 00:02:00 v-Cancel ^
Manual Cycle Time Screen Use the keypad to enter the manual heater on-time duration. Press the [Enter] key to confirm or the down arrow key to cancel.
Enter
Enter
Enter
Enter new value Current: 77.0 77.0 v-Cancel ^
Heater, Overfeed
Press the [Enter] key to make the heater operation dependent or independent of the status of the flow switch SW1.
Note: The relay 3 programming menu appears in this format only when relay 3 has been configured for "Heater" control.
Heater, Low Temperature Setpoint
Enter
Heater, Minimum Time On Heater, Minimum Time Off
Enter new value Current: 00:01:00 00:01:00 v-Cancel ^
Use the keypad to enter the time delay between the setpoint trigger and the heater cycle start. Press the [Enter] key to confirm or the down arrow key to cancel. Use the keypad to enter the low temperature setpoint for heater control. Press the [Enter] key to confirm or the down arrow key to cancel. On Delay Screen Low Temperature Setpoint Screen
ManualTime 00:02:00 On If Temp< 77.0 Off if Sw1 Off-NO <
On DELAY 00:01:00 MinTime On 00:02:00 MinTimeOff 00:02:00 Overfeed 05:00:00
ManualTime 00:02:00<
On If Temp< 77.0 Off if Sw1 Off-YES On DELAY 00:01:00 MinTime On 00:02:00 MinTimeOff 00:02:00 Overfeed 05:00:00
ManualTime 00:02:00 On If Temp< 77.0< Off if Sw1 Off-YES On DELAY 00:01:00 MinTime On 00:02:00 MinTimeOff 00:02:00 Overfeed 05:00:00 ManualTime 00:02:00 On If Temp< 77.0 Off if Sw1 Off-YES < On DELAY 00:01:00 MinTime On 00:02:00 MinTimeOff 00:02:00 Overfeed 05:00:00 ManualTime 00:02:00 On If Temp< 77.0 Off if Sw1 Off-YES On DELAY 00:01:00< MinTime On 00:02:00 MinTimeOff 00:02:00 Overfeed 05:00:00
ManualTime 00:02:00< On If Temp< 77.0 Off if Sw1 Off-YES On DELAY 00:01:00 MinTime On 00:02:00< MinTimeOff 00:02:00 Overfeed 05:00:00 ManualTime 00:02:00 On If Temp< 77.0 Off if Sw1 Off-YES On DELAY 00:01:00 MinTime On 00:02:00 MinTimeOff 00:02:00< Overfeed 05:00:00 ManualTime 00:02:00 On If Temp< 77.0 Off if Sw1 Off-YES On DELAY 00:01:00 MinTime On 00:02:00 MinTimeOff 00:02:00 Overfeed 05:00:00<
Heater, Off if SW1 is Off Heater, Independent of SW1
Enter
Heater, On Delay
Enter
Enter new value Current: 00:02:00 00:02:00 v-Cancel ^
Use the keypad to enter the minimum amount of time the heater will be turned on. Press the [Enter] key to confirm or the down arrow key to cancel. Minimum Time On Screen
Enter
Enter new value Current: 00:02:00 00:02:00 v-Cancel ^
Minimum Time Off Screen Use the keypad to enter the amount of time the heater will be held off before it is allowed to turn on again. Press the [Enter] key to confirm or the down arrow key to cancel.
Enter new value Current: 05:00:00 05:00:00 v-Cancel ^
Overfeed Screen Use the keypad to enter the daily maximum accumulated heater on- time. Press the [Enter] key to confirm or the down arrow key to cancel.
Back
AK110 Programming Screen Navigation, Heater, Rev 3 22 Aug 2008