86
pH > 7.67-OFF 7.50s
ORP 490 -OFF 700s
Alarm Out -OFF
69.0f SW1OFFSW2OFF
Main Status Screen
Name:Main Pool
System
>Programming
Service
Data ( 8:441 )
Communications
Security Setup
Wizards
Serial # 123456
Configuration Menu, Programming
AK110 Programming Screen Navigation, Alarm Out (1 of 2)
EnterBack
1:pH, Mix Time
2:ORP, Mix Time
>3:Alarm Out
A:Alarm
P:Pager1
P:Pager2
P:Pager3
P:Pager4
Programming Setup Screen
Alarm Out, On if Panel Alarm is On
EnterBack
Alarm Out, On if SW1 is Off
Alarm Out, Low ORP Setpoint
Alarm Out, Not On if Panel Alarm is On
Press the [Enter] key to choose
whether the alarm out relay is turned
on when the AK110 front panel
alarm indicator is on.
Enter
Alarm Out, Not On if SW1 is Off
Enter
Enter new value
Current: 630
630
v-Cancel ^
Use the keypad to enter the low
ORP value under which the alarm
out relay will turn on.
Press the [Enter] key to confirm or
the down arrow key to cancel.
Enter
Low ORP Setpoint Screen
Enter
Alarm Out, High pH Setpoint
Enter new value
Current: 8.00
8.00
v-Cancel ^
Use the keypad to enter the high pH
value over which the alarm out relay
will turn on.
Press the [Enter] key to confirm or
the down arrow key to cancel.
High pH Setpoint Screen
Note:
The relay 3 programming menu
appears in this format only when
relay 3 has been configured for
"Alarm Out" control.
The options available on the
Alarm Out Screen programming
menu may vary in accordance
with the chosen configurations for
relays 1 and 2.
Alarm Out, High ORP Setpoint
Enter
High ORP Setpoint Screen
On If Alarm On YES<
On if Sw1 Off-YES
On If ORP< 630
On If ORP> 770
On If pH> 8.00
On If pH< 7.00
On If Temp< 32.0
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
MinTime On 00:00:10
MinTimeOff 00:00:10
On If Alarm On NO <
On if Sw1 Off-YES
On If ORP< 630
On If ORP> 770
On If pH> 8.00
On If pH< 7.00
On If Temp< 32.0
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
MinTime On 00:00:10
MinTimeOff 00:00:10
On If Alarm On YES
On if Sw1 Off-YES <
On If ORP< 630
On If ORP> 770
On If pH> 8.00
On If pH< 7.00
On If Temp< 32.0
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
MinTime On 00:00:10
MinTimeOff 00:00:10
On If Alarm On YES
On if Sw1 Off-NO <
On If ORP< 630
On If ORP> 770
On If pH> 8.00
On If pH< 7.00
On If Temp< 32.0
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
MinTime On 00:00:10
MinTimeOff 00:00:10
On If Alarm On YES
On if Sw1 Off-YES
On If ORP< 630<
On If ORP> 770
On If pH> 8.00
On If pH< 7.00
On If Temp< 32.0
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
MinTime On 00:00:10
MinTimeOff 00:00:10
Press the [Enter] key to choose
whether the alarm out relay is turned
on when the flow switch SW1 is off.
Enter new value
Current: 770
770
v-Cancel ^
Use the keypad to enter the high
ORP value over which the alarm out
relay will turn on.
Press the [Enter] key to confirm or
the down arrow key to cancel.
On If Alarm On YES
On if Sw1 Off-YES
On If ORP< 630
On If ORP> 770<
On If pH> 8.00
On If pH< 7.00
On If Temp< 32.0
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
MinTime On 00:00:10
MinTimeOff 00:00:10
On If Alarm On YES
On if Sw1 Off-YES
On If ORP< 630
On If ORP> 770
On If pH> 8.00<
On If pH< 7.00
On If Temp< 32.0
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
MinTime On 00:00:10
MinTimeOff 00:00:10
Enter
Alarm Out, Low pH Setpoint
Enter new value
Current: 7.00
7.00
v-Cancel ^
Use the keypad to enter the low pH
value under which the alarm out
relay will turn on.
Press the [Enter] key to confirm or
the down arrow key to cancel.
Low pH Setpoint Screen
On If Alarm On YES
On if Sw1 Off-YES
On If ORP< 630
On If ORP> 770
On If pH> 8.00
On If pH< 7.00<
On If Temp< 32.0
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
MinTime On 00:00:10
MinTimeOff 00:00:10
Enter
Alarm Out, Low Temperature Setpoint
Enter new value
Current: 32.0
32.0
v-Cancel ^
Use the keypad to enter the low
temperature value under which the
alarm out relay will turn on.
Press the [Enter] key to confirm or
the down arrow key to cancel.
Low Temperature Setpoint Screen
On If Alarm On YES
On if Sw1 Off-YES
On If ORP< 630
On If ORP> 770
On If pH> 8.00
On If pH< 7.00
On If Temp< 32.0<
On If Temp> 104.0
Off if Sw1 Off-NO
On if Sw2 Off-NO
On If Overfeed YES
On DELAY 00:10:00
MinTime On 00:00:10
MinTimeOff 00:00:10
Back
AK110 Programming Screen Navigation, Alarm Out, Rev 3 22 Aug 2008
10.15
To Next Page
Loading...
