Risco ProSYS Plus - Page 58

64 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

09/2016 Page 58 5IN2371 C

3. If the HandyApp registration email address is not identical to the Installer

Admin email address, the HandyApp will request a RISCO Cloud Installer

Admin login (for initial login only). Enter your RISCO Cloud Installer Admin

Username and Password.

4. The Panel Selection screen appears:

Table of Contents

Default Chapter2
- Table of Contents2
Getting Started6
Main Steps for Initial System Setup6
Important Safety Precautions7
Installation8
Step 1: Creating a Plan for Mounting the System8
- Main Panel Mounting Guidelines8
Step 2: Wiring, Settings, and Module Installations at the Main Panel8
- Power Supply, Ground Wiring and Telephone Wiring8
- Main Panel Wiring Diagram10
- Replacing the Main Panel PCB11
- Setting Main Panel DIP Switches and Jumpers11
- Installing Plug-In Communication & Audio Modules11
- Wiring Other Devices at the Terminal Block12
- Installing a Wired Keypad12
Step 3: Bus Line Installations16
- Bus Line Wiring16
- Describing Bus Devices16
- Describing Bus Detectors and Their Connection Options16
- Wired Expansion Modules Installed on RISCO Bus Lines17
- Describing Installer-Set ID Numbers for Bus Devices18
  - ID Number Formats19
  - Assigning ID Numbers (Setting DIP Switches) for Bus Devices20
- Installing Bus Devices21
Step 4: Connecting Relay Detectors23
- Defining Zone Termination Resistance24
  - Wiring Resistors for Zone Termination Resistance24
  - Zone Termination Configuration Options24
Step 5: Connecting the Backup Battery and Mounting the Main Panel25
- Connecting the Backup Battery25
- Mounting the Main Panel25
System Initialization, Device Allocation, General System Configuration26
Step 1: Working with the Keypad and Installer Menus26
- Describing Dynamic Keypad Menus26
  - Table of Menu Navigational Keys26
  - Designating Labels26
- Entering the Installer Programming Menu at Initial System Setup27
- Subsequently Accessing Installer Menus27
Step 2: Powering-Up and Initializing the System27
- Initial System Power-Up and Language Selection27
- Viewing Zones, Defining Partitions, and Setting the Time & Date28
  - Viewing Zones, Defining Partitions, and Setting Time/Date at Initialization28
  - Viewing & Updating Zones and Defining Partitions after Initialization29
Step 3: Allocating and Configuring Installed Components30
- Auto-Setting Allocation of Communication Modules and Bus Devices30
  - Describing Auto-Setting Results31
- Performing a Bus Test31
- Manually Allocating & Configuring Communication Modules32
- Manually Allocating & Configuring Other Modules and Bus Devices34
Step 4: Allocating Wireless Zones39
- Allocating Wireless Expanders39
- Allocating Wireless Devices39
  - Sending Wireless Device RF Transmissions40
Step 5: Basic Zone Configuration for All Zone Types41
- Defining Basic Parameters41
Step 6: Advanced Zone Configuration for Bus Zones and Wireless Zones44
- Advanced Programming for Bus Zones44
- Advanced Programming for Wireless Zones44
  - Measuring Background Noise Level and Defining Its Threshold Limit45
  - Performing a Wireless Comm. Test for Measuring Signal Strength46
Step 7: Configuring System Communication47
- Defining Primary Communication Channels & Parameters47
- Defining Communication with the Monitoring Station48
  - Enabling Monitoring Station Communication48
  - Defining Monitoring Station Account Parameters48
Step 8: Configuring Cloud Connectivity49
- Enabling / Disabling Cloud Communication49
- Defining RISCO Cloud Connectivity49
Step 9: Configuring Common System Parameters50
- Defining System Users50
- Defining Follow Me Destinations51
  - Enabling Follow Me51
  - Defining Follow Me Parameters51
- Defining System Timers51
Installer Programming52
Step 1: Defining Additional Parameters in the Installer Programming Menu52
Step 2: Exiting Installer Programming Menu after Initial System Configuration52
Step 3: Defining Parameters in Other Installer Menus52
Testing the System53
Installer Responsibilities for Assisting Clients53
Technical Specification54
Licensing Procedure56

Other manuals for Risco ProSYS Plus

Quick User Guide8 pages

Installation And Programming Manual280 pages

Related product manuals

Preview: Risco ProSYS

Preview: Risco ProSYS 16

Risco ProSYS 16

Risco ProSYS 40

Preview: Risco ProSYS 128

Risco ProSYS 128

Preview: Risco ProSYS series

Risco ProSYS series

Preview: Risco ProSYS KP

Risco ProSYS KP

Preview: Risco LightSYS

Preview: Risco LightSYS2

Risco LightSYS2

Preview: Risco Agility 3

Risco Agility 3

Preview: Risco Agility 4

Risco Agility 4

Preview: Risco lightsys 2

Risco lightsys 2