Rockwell Automation Allen-Bradley PowerMonitor 5000 Unit - Page 254

514 pages

To Next Page

To Previous Page

254 Rockwell Automation Publication 1426-UM001J-EN-P - August 2019

Chapter 9 Communication

10. Open RSNetWorx for ControlNet software and click Online.

11. Browse to and select the ControlNet network to which the power monitor

is connected, and then click OK.

12. Wait until the online browse is complete.

Main Page

Default Chapter3
- Table of Contents3
- About this Manual7
- Intended Audience7
- Summary of Changes7
- Additional Resources8
- Catalog Number Explanation8
Chapter 19
- Product Description9
- Safety9
- Powermonitor 5000 Unit Features and Functions10
- Before You Begin14
- Product Disposal14
- Mounting Considerations15
Chapter 218
- Wire the Powermonitor 5000 Unit18
- Connect Communication31
Setup Using the Web Interface49
Chapter 358
- Commands58
- Setup Using Custom Add-On Profile59
- Setup Using Communication69
- Setup Using Optional Software69
Chapter 4 Basic Metering71
- Wiring Diagnostics73
- Wiring Correction78
- Metering Overview80
- Energy Metering81
- Demand Metering83
- Power Metering87
- Voltage, Current, Frequency Metering89
- Configuration Lock91
Chapter 594
Chapter 595
Harmonic Analysis96
- Sag and Swell Detection102
- Waveform Recording (M6 and M8 Model)104
Chapter 6 Logging Overview112
- Waveform Log (M6 and M8 Model)118
- Energy Log134
- Data Log138
- Min/Max Log148
- Load Factor Log155
- Time-Of-Use (TOU) Log156
- Event Log159
- Setpoint Log163
- Alarm Log165
- Power Quality Log (M6 and M8 Model)171
- Trigger Data Log (M6 and M8 Model)176
- Snapshot Log179
- EN 50160 Weekly and Yearly Logs181
Chapter 7 Relay and KYZ Outputs183
- Status Inputs187
- Setpoints191
Chapter 8 Security209
- Date and Time Functions211
- Network Time Synchronization213
- System Error Response217
- Miscellaneous Commands218
Chapter 9 Native Ethernet Communication219
- Optional Controlnet Communication221
- Optional Devicenet Communication221
- Electronic Data Sheet (EDS)222
- Powermonitor 5000 Unit Memory Organization223
- Communication Command Summary224
- Ethernet/Ip Object Model226
- Devicenet and Controlnet Object Model227
- Explicit Messaging227
- Examples: Explicit Message Setup228
- SCADA Applications235
- Controller Applications: Class 1 Connection242
- CIP Energy Object260
Chapter 10265
Update the Powermonitor 5000 Unit Firmware265
- Rockwell Automation Publication 1426-UM001J-EN-P - August266
- Upgrading the Powermonitor 5000 Model and Communication267
- Use the Controlflash Utility to Update Firmware267
- Summary of Data Tables269
Appendix A272
- Data Tables272
- Information Tables429
Appendix B432
Appendix B433
Certifications434
Appendix C Terminal Setup437
- Introduction437
Appendix D Terminal Setup447
- Introduction447
- Compression Algorithm455
IEEE 519 Pass/Fail Capability (M6 and M8 Models)459
Appendix E460
Appendix F460
- IEEE 519 Pass/Fail Results460
- IEEE 519 Short-Term and Long-Term Harmonic Results461
Appendix G463
- Ieee 1159-2009463
- Power Quality Event Classification Per463
- Transients (Category 1.1.3, 1.2.1)(M8 Model)464
- Interruptions) (M6 and M8 Model)465
- Short Duration RMS Variations465
- Long Duration RMS Variations466
- Voltage and Current Imbalance (Category 4.0)467
- Waveform Distortion468
- Flicker (Voltage Fluctuations, Category 6.0)469
- Power Frequency Variations (Category 7.0)470
Introduction473
Appendix H474
- Operation474
- Results478
- Introduction483
Appendix I Power Quality Parameters484
- Introduction493
Appendix J496
- Install the AOP496
Glossary499
Index507
- Rockwell Automation Publication 1426-UM001J-EN-P - August508

Rockwell Automation Allen-Bradley PowerMonitor 5000 Unit - Page 254

Table of Contents

Related product manuals