52
Q&A
Overall / System
01 Can I specify a MIDI channel for each part?
Yes.
The MIDI channel is specied by the “Rx Ch” parameter in the SCENE PART
EDIT screen for each part.
02 Does the sound change as on an analog
synthesizer according to temperature and the
passage of time?
If the Aging function is “ON,” an internal temperature sensor is used to apply
change to some synthesizer sounds (sounds for which the TONE parameter
Pitch Drift is specied), simulating the way in which temperature variation
and the passage of time after startup can aect the sound of an analog
synthesizer.
Turn the Aging function “ON” as described below, and notice how the
sound changes.
1. Press the [MENU] button.
2. Use the [1] knob or [2] knob to select “SYSTEM,” and then
press the [ENTER] button.
3. Use knob [1] to select “Warm-Up,” and use knob [2] to select
either “ON” or “FAST.”
ON: Simulation is on. The status of Pitch Drift will change in
approximately ten minutes, and will subsequently stabilize at the value
of the TONE setting Pitch Drift.
FAST: This mode shortens the change of the ON setting to
approximately ten seconds, allowing you to hear the eect of Pitch
Drift.
FIXED: The internal temperature is xed at the value specied by Aging
Init Temp, and the character of the sound at that point is maintained.
4. Press the [WRITE] button to save the setting.
A conrmation message appears.
03 Can the internal speaker be turned o at all
times?
Yes.
Use the following procedure to turn the internal speaker "OFF."
1. Press the [MENU] button.
2. Use knob [1] or the PAGE [ ] [ ] buttons to select “SYSTEM,”
and then press the [ENTER] button.
3. Use knob [1] to select “Speaker Sw,” and use knob [2] to
select “OFF.”
4. Press the [WRITE] button to save the setting.
A conrmation message appears.
04 Is this unit equipped with Bluetooth
functionality?
Yes, it is.
You can use its Bluetooth functionality in the following ways.
Bluetooth audio
Music played back from your mobile device can be mixed with the
sound of the internal sound engine, and output from this unit.
* To adjust the volume of your mobile device’s playback, make adjustments on
the playback device.
Bluetooth MIDI
You can use this unit as a MIDI keyboard for a music app.
05 How do I save a sound that I created?
To completely save and reproduce the sound that you're currently hearing,
you must save both the tones and the scene.
Save this data as follows.
Saving the tone
1. Press the [WRITE] button.
2. Use the [1] knob or [2] knob to select “PART* TONE” (* is the
part to which the tone you’re saving is assigned), and then
press the [ENTER] button.
3. Use the [1] knob to select the save-destination, and then
press the [ENTER] button.
Use the [1] knob to select the save-destination, and then press the
[ENTER] button.
If you want to rename the tone that’s being saved, use the PAGE [<] [>]
buttons to move the cursor and use the [2] knob to specify characters.
4. Press the [ENTER] button.
A conrmation message appears.
If you decide to cancel, press the [EXIT] button.
5. To execute, press the [ENTER] button.
Saving the scene
1. Press the [WRITE] button.
2. Use the [1] knob or [2] knob to select “SCENE,” and then
press the [ENTER] button.
3. Use the [1] knob or [2] knob to select the save-destination,
and then press the [ENTER] button.
If you want to rename the scene that’s being saved, use the PAGE [<] [>]
buttons to move the cursor and use the [2] knob to specify characters.
4. Press the [ENTER] button.
A conrmation message appears.
If you decide to cancel, press the [EXIT] button.
5. To execute, press the [ENTER] button.
To Next Page
Loading...
Need help?
Power
Display
Audio
Weight and Dimensions
