Roland Jupiter-Xm Reference Manual

43
Reference Manual Ver. 1.5 and later
MEMO
If the WRITE MENU screen appears, use the [1] or [2] knob to select
“SYSTEM,” and then press the [ENTER] button.
2. To execute, press the [ENTER] button.
System Parameter List
Parameter
[1] knob
Value
[2] knob
Explanation
AGING
Warm-up
OFF, ON, FAST,
FIXED
Species whether the character of the sound
(pitch variance) changes according to the
varying internal temperature of this unit.
This has an eect only on analog synthesizer
models.
The internal temperature value is shown in the
upper right of the top screen of the scene.
OFF: The character of the sound is not aected
by the temperature. Nor is there a temperature
indication in the SCENE screen.
ON: The internal temperature starts at the
value specied by Aging Init Temp, and
changes to the actual temperature (REAL).
Although it depends on the temperature
dierence, the REAL temperature is reached
in approximately ten minutes. After reaching
the REAL temperature, the setting follows the
actual temperature change.
FAST: The internal temperature starts at the
value specied by Aging Init Temp, and then
quickly (in approximately ten seconds) changes
to the actual temperature (REAL) when you
play the keyboard. After reaching the REAL
temperature, the setting follows the actual
temperature change.
FIXED: The internal temperature is xed at
the value specied by Aging Init Temp, and
the character of the sound is maintained at
that point.
Init Temp
REAL, 0–60°C/32–
140°F
Species the initial internal temperature for
Warm-up.
REAL: The internal temperature that is actually
measured will be the initial temperature.
0–60°C/32–140°F: Virtually species an initial
internal temperature (Celsius).
Age
OFF, 1–100years
Simulates the eect of aging on the internal
components of an analog synthesizer.
Higher values aect the sound similarly to the
equivalent number of years of aging.
This is valid only for sounds of an analog
synthesizer model.
GENERAL
MasterTune
415.3–466.2 [Hz]
Adjusts the overall tuning.
The displayed value is the frequency of the A4
key (middle A).
MasKeyShift
-24–24
Shifts the JUPITER-Xm’s overall pitch range in
semitone steps.
ScaleTuneSw
OFF, ON
Species whether the scene’s SCALE TUNE
setting is enabled (ON) or disabled (OFF).
USB In Lev
0–127
Adjusts the audio input level of the USB
COMPUTER port.
USB Out Lev
0–127
Adjusts the audio output level to the USB
COMPUTER port.
AuxIn/BT InLev
0–127
Adjusts the input level of the AUX IN jack and
BT In.
USB Audio Thru
OFF, ON
Species whether the audio input of the USB
COMPUTER port is mixed into the audio output
of the USB COMPUTER port.
If you don’t want it to be output as audio, turn
this “OFF.”
AUXIN USB Thru
OFF, ON
Species whether the input from the AUX IN
jack is mixed into the audio output of the USB
COMPUTER port.
If you don’t want it to be output as audio, turn
this “OFF.”
LineOut Gain
-12–0–+12 [dB] Adjusts the output gain of OUTPUT/PHONES.
Speaker Sw
OFF, ON, AUTO
Species whether sound is output from this
unit's speakers.
OFF: Sound is not output from the speakers.
ON: Sound is output from the speakers.
AUTO: The "OFF" setting is used if headphones
are inserted, and the "ON" setting is used if
they are not inserted.
Parameter
[1] knob
Value
[2] knob
Explanation
SPOut Gain
-12–0 [dB] Adjusts the output gain of the speakers.
Auto O
OFF, 30 [min],
240 [min]
Species whether the unit will turn o
automatically after a certain time has elapsed.
If you don’t want the unit to turn o
automatically, choose “OFF” setting.
LED On Bright
0–31 Adjusts the brightness when the LEDs are lit.
LED OBright
0–30
When the unit is operating on the AC adaptor,
you can specify that an LED will remain lit at
a modied brightness even when it is in the
“o ” state.
If this is set to 0, the LED will be unlit when o.
LCD Contrast
1–10 Adjusts the contrast of the display.
Scene Lock
OFF, ON
Species whether a conrmation screen
appears when you switch scenes.
OFF: When you switch scenes, the scene
changes immediately, and no conrmation
screen appears.
ON: When you switch scenes, a conrmation
screen appears.
To switch scenes, use the PAGE [<] [>] buttons
to select “ Yes ,” and then press the [ENTER]
button.
Startup Scene
01-01–16-16 Species the scene that is selected at start-up.
ARPEGGIO
Set Tone
OFF, ON
Species whether the current sound settings
are kept while only the phrase is switched
(OFF) or both the phrase and the sound
settings are switched (ON).
Set DrumKit
OFF, ON
Species whether the current sound settings
are kept while only the rhythm is switched
(OFF) or both the rhythm and the sound
settings are switched (ON).
Set Tempo
OFF, ON
Species whether the current tempo setting is
kept while only the rhythm is switched (OFF)
or both the rhythm and the tempo settings are
switched (ON).
Arp Sync
OFF, BEAT,
MEASURE
Species how the arpeggio is synchronized
when the JUPITER-X is connected to
an external device and is playing in
synchronization.
OFF: The arpeggio does not synchronize to
the measure or beat. The arpeggio starts the
moment that MIDI messages are received.
BEAT: The arpeggio synchronizes to the beat.
The arpeggio starts at the next beat after MIDI
is received.
MEASURE: The arpeggio synchronizes to the
measure. The arpeggio starts at the rst beat of
the next measure after MIDI is received.
TEMPO/SYNC
Tempo
20.00–300.00 Species the system tempo.
Tempo Src
SCENE, SYS
When you switch scenes, this setting species
whether to use the system tempo (SYS) or the
tempo stored in the scene (SCENE).
Sync Mode
AUTO, INT, MIDI,
USB COM,
USB MEM
Species the synchronization signal according
to which the JUPITER-Xm operates.
Sync Out
OFF, MIDI,
USB COM,
MIDI/USBCM,
USB MEM, ALL
Species the connector from which MIDI clock
messages etc. are output.
Bluetooth
Bluetooth Sw
OFF, ON
Enables (ON) or disables (OFF) Bluetooth
communication.
Pairing
- Executing pairing for Bluetooth audio.
Bluetooth ID
OFF, 1–9
Species the number added to the end of this
unit’s device name shown in a Bluetooth-
connected app.
MIDI
Ctrl Ch
1–16, OFF
Species the MIDI receive channel on which
MIDI messages (program change and bank
select) from an external MIDI device can be
received to switch programs.
If you don’t want programs to be switched
from a connected MIDI device, turn this “OFF.”
Ctrl Src Sel
SYS, SCENE
SYS: SysCtrlSrc1–4 are used for tone control.
SCENE: The scene’s CtrlSrc1–4 settings are
used for tone control.

Roland Jupiter-Xm Specifications

Power

dc voltage	12 V
current draw	1, 500 mA
battery type	Ni-MH battery (AA, HR6) x 8
battery life	approximately 3.5 hours

Display

display type	Graphic LCD
display resolution	128 x 64 dots

Audio

speaker amplifier power	4 W x 2
full range speaker size	3.5 x 8 cm x 2
tweeter size	2 cm x 2

Weight and Dimensions

weight	4.4 kg, 9 lbs 12 oz
width	576 mm, 22-11/16 inches
depth	308 mm, 12-1/8 inches
height	93 mm, 3-11/16 inches