EasyManuals Logo

Rosemount 3051SFC_A User Manual

Rosemount 3051SFC_A
268 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #170 background imageLoading...
Page #170 background image
Reference Manual
00809-0100-4809, Rev DA
Appendix A: Specifications and Reference Data
September 2015
162
Specifications and Reference Data
A.11.3 Physical specifications
Temperature measurement
Integral RTD
100 Ohm platinum RTD
4-wire RTD ( = 0.00385)
Remote RTD
100 Ohm platinum RTD, spring loaded with
1
/2-in.
NPT nipple and union (078 series with Rosemount 644
housing)
Thermowell
1
/2-in.
1
/2-in NPT, 316 Stainless Steel with
1
/2-in. weld
couplet (same as specified pipe material).
Housing connections
1
/2–14 NPT, G
1
/2, and M20 1.5 conduit. HART interface
connections fixed to terminal block for output code A
Annubar sensor material
316 Stainless Steel
Alloy C-276
Mounting material
Carbon Steel (A105)
316 Stainless Steel
Chrome-Moly Grade F-11
Chrome-Moly Grade F-22
Chrome-Moly Grade F-91
Annubar sensor type
Pak-Lok model (option P)
Provided with a compression sealing mechanism rated
up to 600# ANSI (1440 psig at 100 °F [99 bar at 38 °C])
–150 to 850 °F (–101 to 454 °C)
Not available for steam above 600 °F (315 °C)
Flanged with opposite side support model (option F)
Provided with opposite side support, which is the
same material as the pipe and requires a second pipe
penetration
Sensor flange is the same material as the Annubar
sensor and the mounting flange is the same material
as the pipe material
Flanged mounting hardware: nuts, studs, and gaskets
(DIN units supplied without nuts, studs, and gaskets)
SST: (–300 to 850 °F [–184 to 454 °C])
Alloy C-276: (–150 to 1250 °F [-101 to 677 °C])
Flange–Lok model (option L)
Flange-Lok assembly is supplied in 316 SST material.
Flange-Lok mounting hardware: nuts, studs, and
gaskets (DIN units supplied without nuts, studs, and
gaskets)
150 to 850 °F (-101 to 454 °C)
Not available for steam above 600 °F (315 °C)
Flo-tap models (options G and M)
Opposite side support is not available
Threaded connection is not available with sensor size
3
Gear Drive is not available with sensor size 1
Packing gland required
Packing Gland Material Temperature Limits
PTFE: –40 to 400 °F (–40 to 204 °C)
Graphite: –150 to 850 °F (-101 to 454 °C)
Isolation valve included
The isolation valve will carry the same pressure
rating as the sensor flange and mounting flange
specified in the mounting type
Isolation valves are not supplied with DIN flanges
and must be customer supplied
For threaded Flo-tap models, the isolation valve NPT
size is 1
1
/4-in. (sensor size 1) and 2-in. (sensor size 2).

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Rosemount 3051SFC_A and is the answer not in the manual?

Rosemount 3051SFC_A Specifications

General IconGeneral
BrandRosemount
Model3051SFC_A
CategoryMeasuring Instruments
LanguageEnglish

Related product manuals