Rosemount 3051SFC_A User Manual

Reference Manual
00809-0100-4809, Rev DA
Appendix B: Product Certifications
September 2015
225
Product Certifications
Markings: IS CL I, DIV 1, GP A, B, C, D; CL II, DIV 1, GP E,
F, G; Class III; DIV 1 when connected per
Rosemount drawing 02051-1009; Class I,
Zone 0; AEx ia IIC T4; NI CL 1, DIV 2, GP A, B,
C, D; T4(-50 °C 
 T
a
 +70 °C); Type 4x
IE USA FISCO
Certificate: 3033457
Standards: FM Class 3600 – 1998,
FM Class 3610 – 2007,
FM Class 3611 – 2004, FM Class 3810 – 2005
Markings: IS CL I, DIV 1, GP A, B, C, D when connected
per Rosemount drawing 02051-1009
(-50 °C 
 T
a
 +60 °C); Type 4x
E6 Canada Explosion-Proof, Dust Ignition Proof
Certificate: 2041384
Standards: CAN/CSA C22.2 No. 0-10,
CSA Std C22.2 No. 25-1966,
CSA Std C22.2 No. 30-M1986,
CAN/CSA-C22.2 No. 94-M91,
CSA Std C22.2 No.142-M1987,
CAN/CSA-C22.2 No.157-92,
CSA Std C22.2 No. 213-M1987,
CAN/CSA-E60079-0:07,
CAN/CSA-E60079-1:07,
CAN/CSA-E60079-11-02,
CAN/CSA-C22.2 No. 60529:05,
ANSI/ISA-12.27.01–2003
Markings: Explosion-Proof for Class I, Divisions 1,
Groups B, C, and D. Dust-Ignition Proof for
Class II and Class III, Division 1, Groups E, F,
and G. Suitable for Class I, Division 2; Groups
A, B, C, and D for indoor and outdoor
hazardous locations. Class I Zone 1 Ex d IIC
T5. Enclosure type 4X, factory sealed. Single
Seal.
I6 Canada Intrinsic Safety
Certificate: 2041384
Standards: CSA Std. C22.2 No. 142 - M1987,
CSA Std. C22.2 No. 213 - M1987,
CSA Std. C22.2 No. 157 - 92,
CSA Std. C22.2 No. 213 - M1987,
ANSI/ISA 12.27.01 – 2003,
CAN/CSA-E60079-0:07,
CAN/CSA-E60079-11:02
Markings: Intrinsically safe for Class I, Division 1,
Groups A, B, C, and D when connected in
accordance with Rosemount drawings
02051-1008. Temperature code T3C. Class I
Zone 1 Ex ia IIC T3C. Single Seal. Enclosure
Type 4X
Europe
E1 ATEX Flameproof
Certificate: KEMA 08ATEX0090X
Standards: EN60079-0:2006, EN60079-1:2007,
EN60079-26:2007
Markings: II 1/2 G Ex d IIC T6 IP66
(–50 °C 
 T
a
65 °C);
II 1/2 G Ex d IIC T5 IP66
(–50 °C 
 T
a
80 °C)
Special Conditions for Safe Use (X):
1. The Ex d blanking elements, cable glands and wiring
needs to be suitable for a temperature of 90 °C.
2. This device contains a thin wall diaphragm. Installation,
maintenance and use shall take into account the
environmental conditions to which the diaphragm will
be subjected. The manufacturer’s instructions for
maintenance shall be followed in detail to assure safety
during its expected lifetime.
3. In case of repair, contact the manufacturer for
information on the dimensions of the flameproof joints.
I1 ATEX Intrinsic Safety
Certificate: Baseefa08ATEX0129X
Standards: EN60079-0:2012, EN60079-11:2012
Markings: II 1 G Ex ia IIC T4 Ga (-60 °C 
 T
a
 +70 °C)
Special Conditions for Safe Use (X):
1. If the equipment is fitted with an optional 90 V transient
suppressor, it is incapable of withstanding the 500V
isolation from earth test and this must be taken into
account during installation.
2. The enclosure may be made of aluminum alloy and
given a protective polyurethane paint finish; however
care should be taken to protect it from impact and
abrasion when located in Zone 0.
Table 11. Input Parameters
Parameters
HART Fieldbus/PROFIBUS
Voltage U
i
30 V 30 V
Current I
i
200 mA 300 mA
Power P
i
1 W 1.3 W
Capacitance C
i
0.012 F 0 F
Inductance L
i
0 mH 0 mH

Rosemount 3051SFC_A Specifications

General

Brand	Rosemount
Model	3051SFC_A
Category	Measuring Instruments
Language	English