Sartorius Combics 2 CAIXS2 - Setup Menu (Device Settings); CAL.ADJ Calibration, adjustment

130 Operating Instructions Combics CAIXS2
Menu Structure
TOLA Tola/tol
1)
1.7.18
BAHT Baht/bat
1)
1.7.19
MESGHAL Mesgahl/MS
1)
1.7.20
TON tons/t 1.7.21
1.DIS.DIG. Display accuracy 1.8
ALL all digits 1.8.1*
-1.WT.CHA reduced by one digit 1.8.2
RES.*10 10-fold increased resolution 1.8.14
+DIV. 2 Increase resolution by 2 scale intervals 1.8.15
+DIV. 1 Increase resolution by 1 scale interval 1.8.16
CAL.ADJ Calibration, adjustment 1.9
CAL.EXT. External calibration/adjustment with default weight 1.9.1*
CAL.E.AUT. External cal./adjustment, weight is detected (see 1.18.1) 1.9.2
CAL.E.USR. External calibr./adjustment with user-defined weight 1.9.3
CAL.INT. Internal calibration/adjustment (for IS scales only) 1.9.4
INT.LIN. Internal linearization (for IS scales only) 1.9.5
1)
EXT.LIN. External linearization with default weights 1.9.6
1)
LIN.E.USR External linearization with user-defined weights 1.9.7
1)
SET.PREL. Set the preload 1.9.8
DEL.PREL. Delete the preload 1.9.9
BLOCKED Key blocked 1.9.10
CAL.SEQ. Calibration/adjustment sequence 1.10
AUTOMAT Calibration with automatic adjustment 1.10.1
MANUAL Calibration with manual adjustment 1.10.2*
ZERORNG. Zero range 1.11
1 PERC. 1 percent/max.load 1.11.1
2 PERC. 2 percent/max.load 1.11.2
5 PERC. 5 percent/max.load 1.11.3*
INIT.ZER. Zero at power on 1.12
1 PERC. 1 percent/max.load 1.12.1*
2 PERC. 2 percent/max.load 1.12.2
5 PERC. 5 percent/max.load 1.12.3
ON.TARE Tare/zero at power on 1.13
ON On 1.13.1*
OFF Off 1.13.2
ISOCAL Adjustment prompt 1.15
OFF Off 1.15.1*
ADJ.PROM On 1.15.2
CAL.EXT External calibration/adjustment 1.16
ACTIVATED Activated 1.16.1*
BLOCKED Blocked 1.16.2
CAL.UNIT Weight unit for calibration 1.17
GRAM gram 1.17.1*
KILOGR. Kilogram 1.17.2
TONS ton 1.17.3
POUND pound 1.17.4
MAN.EXT.W Manual entry of external weights 1.18
Cal.Adj. cal/adj. weight 1.18.1
LIN.WT.1 linearization weight 1 1.18.2
1)
LIN.WT.2 linearization weight 2 1.18.3
1)
LIN.WT.3 linearization weight 3 1.18.4
1)
LIN.WT.4 linearization weight 4 1.18.5
1)
ADJ.W/O.W Adjustment without weights
1)
1.19
NOM.LOAD Nominal load 1.19.1
RESOLUT resolution 1.19.2
SENSIT.1 Sensitivity 1 1.19.3
SENSIT.2 Sensitivity 2 1.19.4
SENSIT.3 Sensitivity 3 1.19.5
SENSIT.4 Sensitivity 4 1.19.6
ZER.POIN Zero point 1.19.7
SAVE Save parameters 1.19.8
GEOG.DAT Geographical data
1)
1.20
LATITUD latitude 1.20.1
ALTITUD altitude 1.20.2
GRAVITY gravitational acceleration 1.20.3
SAVE Save parameters 1.20.4
1)
Only in Service mode