MX-M316N SIMULATION 6 – 55
48-5
Purpose
Adjustment
Function (Purpose)
Used to correction the scan image magnifi-
cation ratio (in the sub scanning direction).
Section
Scanner section
Operation/Procedure
1) Select a target adjustment item with scroll key on the touch
panel.
2) Enter the set value with 10-key.
3) Press [OK] key.
The set value is saved.
When the image magnification ratio in the sub scanning direction is
adjusted with SIM48-1, and a different magnification ratio is speci-
fied, and the image magnification ratio is not satisfactory, perform
this adjustment.
When there is an error in the image magnification ratio in reduction,
change the adjustment value in the high speed mode. When there
is an error in the image magnification ratio in enlargement, change
the adjustment value in the low speed mode.
48-6
Purpose
Adjustment
Function (Purpose)
Used to adjust the rotation speed of each
motor.
Section
Operation/Procedure
1) Select an adjustment target mode with [COLOR] [MONO]
[HEAVY] keys on the touch panel.
2) Select a target adjustment item with scroll key on the touch
panel.
3) Enter the set value with 10-key.
4) Press [OK] key.
The set value is saved.
When the adjustment value is increased, the speed is increased,
and vice versa. A change of 1 in the adjustment value corresponds
to a change of about 0.1% in the speed.
49
49-1
Purpose
Function (Purpose) Used to perform the firmware update.
Section
Operation/Procedure
1) Save the firmware to the USB memory.
2) Insert the USB memory into the main unit. (Use USB I/F of the
operation panel section.)
3) Select a target firmware file for update with the touch panel.
4) Select a target firmware.
Press [ALL] key to select all the Firmware collectively.
5) Press [EXECUTE] key.
6) Press [YES] key.
The selected firmware is updated.
When the operation is normally completed, "COMPLETE" is
displayed. When terminated abnormally, "ERROR" is dis-
played.
49-3
Purpose
Function (Purpose) Used to update the operation manual in the
HDD.
Section
Operation/Procedure
1) Insert the USB memory into the main unit.
* When the USB is not inserted, "INSERT A STORANGE E-
MANUAL STORED ON" is displayed. When [OK] key is
pressed, the display is shifted to the folder select menu 1.
2) Press the folder button of the operation manual data. (The dis-
play is shifted to the operation manual update menu.)
The current version and the update version are displayed.
3) Press [EXECUTE] key.
[EXECUTE] key is highlighted, and [YES] [NO] keys becomes
active from gray out.
4) When [YES] key is pressed, the selected operation manual is
updated.
When update is completed normally, "COMPLETE" is dis-
played. When terminated abnormally, "ERROR" is displayed.
Item/Display Content
Setting
range
Default
value
A MR (HI) Scanner motor (High speed) 1 - 99 50
B MR(MID) Scanner motor (Reference speed) 1 - 99 50
C MR(LO) Scanner motor (Low speed) 1 - 99 50
D SPF(HI) Document feed (SPF) motor
(High speed)
1 - 99 50
E SPF(MID) Document feed (SPF) motor
(Reference speed)
1 - 99 50
Item/
Display
Content
Setting
range
Default
value
A POM Paper exit motor correction value 1 - 99 50
B ADUM ADU motor correction value 1 - 99 50
C MM Main motor correction value 1 - 99 50
Item/Display Content
Error display in
case of abnormality
ICU (MAIN) ICU Main section ICUM
ICU (BOOTM) ICU Boot section main ICUBM
ICU (BOOTCN) ICU Boot section CN ICUCN
ICU (SUB) ICU Sub section (ARM9) ICUS
LANGUAGE Language support data
program
LANG
GRAPHIC Graphic data for L-LCD GRAPH
SLIST SLIST data for L-LCD SLIST
PCU (BOOT) PCU Boot section PCUB
PCU (MAIN) PCU Main section PCUM
FIN (BOOT) Inner finisher boot section FINB
FIN (MAIN) Inner finisher main section FINM
SCU (BOOT) SCU Boot section SCUB
SCU (MAIN) SCU Main section SCUM
FAX (BOOT) FAX1 Boot section FAXB
FAX (MAIN) FAX1 Main section FAXM
ANIMATION Animation data ANIME
WEB HELP WEB help WEBHP
1
: ‘15/Aug.
1
To Next Page
Loading...
