Siemens Argus 7SR21 - Binary Output Config

7SR220 Settings Guide
Unrestricted ©2018 Siemens Protection Devices Limited Page 99 of 107
Description Range Default
E11
Quick Logic equation 11 operated
Combination of ( BO1, BO2, BO3,
BO4, BO5, BO6, BO7, BO8, BO9,
BO10, BO11, BO12, BO13, BO14,
L1, L2, L3, L4, L5, L6, L7, L8, L9,
L10, L11, L12, L13, L14, V1, V2,
V3, V4, V5, V6, V7, V8, V9, V10,
V11, V12, V13, V14, V15, V16 )
----------------------
----------------------
E12
Quick Logic equation 12 operated
Combination of ( BO1, BO2, BO3,
BO4, BO5, BO6, BO7, BO8, BO9,
BO10, BO11, BO12, BO13, BO14,
L1, L2, L3, L4, L5, L6, L7, L8, L9,
L10, L11, L12, L13, L14, V1, V2,
V3, V4, V5, V6, V7, V8, V9, V10,
V11, V12, V13, V14, V15, V16 )
----------------------
----------------------
E13
Quick Logic equation 13 operated
Combination of ( BO1, BO2, BO3,
BO4, BO5, BO6, BO7, BO8, BO9,
BO10, BO11, BO12, BO13, BO14,
L1, L2, L3, L4, L5, L6, L7, L8, L9,
L10, L11, L12, L13, L14, V1, V2,
V3, V4, V5, V6, V7, V8, V9, V10,
V11, V12, V13, V14, V15, V16 )
----------------------
----------------------
E14
Quick Logic equation 14 operated
Combination of ( BO1, BO2, BO3,
BO4, BO5, BO6, BO7, BO8, BO9,
BO10, BO11, BO12, BO13, BO14,
L1, L2, L3, L4, L5, L6, L7, L8, L9,
L10, L11, L12, L13, L14, V1, V2,
V3, V4, V5, V6, V7, V8, V9, V10,
V11, V12, V13, V14, V15, V16 )
----------------------
----------------------
E15
Quick Logic equation 15 operated
Combination of ( BO1, BO2, BO3,
BO4, BO5, BO6, BO7, BO8, BO9,
BO10, BO11, BO12, BO13, BO14,
L1, L2, L3, L4, L5, L6, L7, L8, L9,
L10, L11, L12, L13, L14, V1, V2,
V3, V4, V5, V6, V7, V8, V9, V10,
V11, V12, V13, V14, V15, V16 )
----------------------
----------------------
E16
Quick Logic equation 16 operated
Combination of ( BO1, BO2, BO3,
BO4, BO5, BO6, BO7, BO8, BO9,
BO10, BO11, BO12, BO13, BO14,
L1, L2, L3, L4, L5, L6, L7, L8, L9,
L10, L11, L12, L13, L14, V1, V2,
V3, V4, V5, V6, V7, V8, V9, V10,
V11, V12, V13, V14, V15, V16 )
----------------------
----------------------
Trip Contacts
Assigns Output Contact as trip contact for fault trigger
BO1, BO2, BO3, BO4, BO5, BO6,
BO7, BO8, BO9, BO10, BO11,
BO12, BO13, BO14
----------------------
----------------------
Hand Reset Outputs
Assigns Output Contact as hand reset contact
BO1, BO2, BO3, BO4, BO5, BO6,
BO7, BO8, BO9, BO10, BO11,
BO12, BO13, BO14
----------------------
----------------------
Pickup Outputs
Selects which outputs can operate because a pickup condition
exists
BO1, BO2, BO3, BO4, BO5, BO6,
BO7, BO8, BO9, BO10, BO11,
BO12, BO13, BO14
--------------
Pulsed Outputs
Selects which outputs are pulsed. The pulse width is set by
the Min Operate Time setting for each output
BO1, BO2, BO3, BO4, BO5, BO6,
BO7, BO8, BO9, BO10, BO11,
BO12, BO13, BO14
--------------
3.13.2. Binary Output Config (Variants may differ)
Description Range Default
Trip Contacts
The Binary Outputs selected by this setting are classed as Trip
contacts. (When any of these BOs operate the Trip LED is lit,
CB Fail is started, if enabled, & a Fault Record is stored)
Combination of ( BO1, BO2, BO3,
BO4, BO5, BO6, BO7, BO8, BO9,
BO10, BO11, BO12, BO13, BO14 )
--------------