Sony HAP-S1 Service Manual

HAP-S1
89
Pin No. Pin Name I/O Description
H12 GND40 - Ground terminal
H13 VDDARM_CAP1 O Internal regulator output terminal
H14 VDDARM_IN1 - Power supply terminal for the cores regulator (+1.42V)
H15 GND41 - Ground terminal
H16 VDDSOC_IN1 - Power supply terminal for the SOC and PU regulators (+1.42V)
H17 VDDPU_CAP1 O Internal regulator output terminal
H18 GND42 - Ground terminal
H19 EIM_A25 I Interrupt signal input from the FPGA
H20 EIM_D21 I VBUS power over current detection signal input terminal for the USB connector
H21 EIM_D31 - Not used
H22, H23 EIM_A20, EIM_A21 I Boot mode setting terminal Fixed at “L”
H24 EIM_CS0 O Serial data transfer clock signal output to the FPGA
H25 EIM_A16 I Boot mode setting terminal Fixed at “L”
J1 HDMI_REF - Not used
J2 GND47 - Ground terminal
J3 HDMI_D1M - Not used
J4 HDMI_D1P - Not used
J5 HDMI_CLKM - Not used
J6 HDMI_CLKP - Not used
J7 NVCC_JTAG O Internal regulator output terminal
J8 GND48 - Ground terminal
J9 VDDHIGH_IN2 - Power supply terminal for the +2.5V regulator (+3.3V)
J10 VDDHIGH_CAP2 O Internal regulator output terminal (+2.5V)
J11 VDDARM23_CAP2 O Internal regulator output terminal Not used
J12 GND44 - Ground terminal
J13 VDDARM_CAP2 O Internal regulator output terminal
J14 VDDARM_IN2 - Power supply terminal for the cores regulator (+1.42V)
J15 GND45 - Ground terminal
J16 VDDSOC_IN2 - Power supply terminal for the SOC and PU regulators (+1.42V)
J17 VDDPU_CAP2 O Internal regulator output terminal
J18 GND46 - Ground terminal
J19, J20 EIM_D29, EIM_D30 - Not used
J21, J22 EIM_A23, EIM_A18 I Boot mode setting terminal Fixed at “L”
J23 EIM_CS1 O Confi guration data output to the FPGA
J24 EIM_OE - Not used
J25 EIM_DA1 I Boot mode setting terminal Fixed at “L”
K1 HDMI_HPD - Not used
K2 HDMI_DDCCEC - Not used
K3 HDMI_D2M - Not used
K4 HDMI_D2P - Not used
K5 HDMI_D0M - Not used
K6 HDMI_D0P - Not used
K7 NVCC_MIPI - Power supply terminal for the MIPI interface (+2.5V)
K8 GND53 - Ground terminal
K9 VDDARM23_IN1 - Power supply terminal for the cores regulator Not used
K10 GND49 - Ground terminal
K11 VDDARM23_CAP3 O Internal regulator output terminal Not used
K12 GND50 - Ground terminal
K13 VDDARM_CAP3 O Internal regulator output terminal
K14 VDDARM_IN3 - Power supply terminal for the cores regulator (+1.42V)
K15 GND51 - Ground terminal
K16 VDDSOC_IN3 - Power supply terminal for the SOC and PU regulators (+1.42V)
K17 VDDPU_CAP3 O Internal regulator output terminal
K18 GND52 - Ground terminal
K19 NVCC_EIM0 - Power supply terminal for the EMI interface (+3.3V)
K20 EIM_RW I Boot mode setting terminal Fixed at “L”
K21 EIM_EB0 I Boot mode setting terminal Fixed at “L”
K22 EIM_LBA I Boot mode setting terminal Fixed at “L”
K23 EIM_EB1 I Boot mode setting terminal Fixed at “L”

Sony HAP-S1 Specifications

General

Product color	Silver
Audio formats supported	AAC, AIFF, ALAC, FLAC, LPCM, MP3, WAV, WMA
Impedance	16 Ω
Frequency range	10 - 100000 Hz
Audio output channels	2.0 channels
Signal-to-Noise Ratio (SNR)	100 dB
Channels quantity	2 channels
Wi-Fi	Yes
Wi-Fi standards	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Automatic synchronization	You don't have to change personal settings when first connecting your device. Your device is automatically synchronized with the settings of your car, so once you have done it for the car, that's it!
Storage media type	HDD
Total storage capacity	500 GB
HDCP	No
Headphone outputs	1
USB 2.0 ports quantity	2
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity	0
AC input voltage	230 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.3 W
Display diagonal	4.3 \

Weight and Dimensions

Width	- mm
Weight	- g