TDK-Lambda Genesys Series

Other manuals for TDK-Lambda Genesys Series

Technical Manual64 pages

Manual44 pages

Instruction Manual28 pages

Need help?

Do you have a question about the TDK-Lambda Genesys Series and is the answer not in the manual?

Summary

Specifications

2.2. LAN Specifications

Details electrical, network configuration, and protocol specifications for the LAN interface.

Select the Control Method

3.2. LAN, Local, or Serial Control Modes

Explains how to enable LAN, Local, or Serial control modes.

3.2.3. Select LAN Remote Mode

LAN Option Rear Panel View

Connect to Network

Power-up the LAN Power Supply

IP Addresses

Hostnames

LAN Setup

5.1. View the IP and MAC Addresses

5.2. Change the IP Address

Provides steps to change the IP address using the front panel controls.

LAN Reset

Default LAN Settings

Logging In

DC Power Page

6.5.1. DC Power → Output Page

Details the output page for viewing measurements and setting voltage/current.

DC Power → Protection Page

DC Power → System Page

DC Power → Utility Page

LAN Page

6.6.1. LAN → Configure Page

Details the 'Configure' panel for setting IP address source, subnet, gateway, etc.

LAN → Configure → Modify Page

DHCP Enabled; Auto IP

Static IP

LAN → Advanced Page

LAN → Users Page

Programming Using VISA Drivers

7.1. VISA Description

7.3. Opening the VISA Connection

SCPI Command Reference

11.1. Command Syntax

Details general SCPI rules, character sets, abbreviations, and syntax conventions.

Configuring the Output

11.2.1. Set the Voltage Limit

Explains how to set the output voltage limit for the power supply.

11.2.2. Set the Current Limit

Explains how to set the output current limit for the power supply.

Set the Output ON or OFF

Measuring the Output

11.3.1. Measure the Output Voltage

Explains how to query the measured output voltage.

11.3.2. Measure the Output Current

Explains how to query the measured output current.

Operating Modes

11.4.1. Read CV or CC Modes

11.4.2. Setting Local or Remote Modes

Set Auto-Restart or Safe-Start Modes

Output Protection

11.5.1. Set Over-Voltage Protection

Explains how to set the over-voltage protection level.

Read Over-Voltage Tripped

Set Under-Voltage Limit

Set Foldback Protection

Read Foldback Tripped

LAN Specific Commands

11.6.1. Blinking the Identify LED

Reset the Hostname and Description

Reset the LAN Settings

Reset the Power Supply

Save All Settings

Recall All Settings

Error and Status Commands

11.8.1. Read System Error

Explains reading the SYSTEM:ERROR queue for status and error messages.

Read Power Supply Shut-Down Faults

Clear Status

Read the Status Byte Register

Read the Standard Event Status Event Register

Read the Operational Condition - Condition Register

Read the Operational Condition Event Register

Read the Questionable Condition Condition Register

Read the Questionable Condition Event Register

RS-485 Multi-drop Commands

Configure the LAN Supply

12.2.1. To Set Up the Master Power Supply

12.2.2. To Set the RS-485 Address

Explains how to set the RS-485 address for multi-drop supplies.

Connect and Configure the RS-485 Supplies

12.3.1. To Verify the Multi-drop is Enabled

12.3.2. To Set Up an RS-485 Chain

Multi-drop Programming Using SCPI Commands

12.4.1. Selecting One Power Supply in a Multi-drop Chain

12.4.2. Global Commands in a Multi-drop Chain

Details commands that affect all supplies in a multi-drop chain.

Error and Status Registers

SYSTEM:ERROR? MESSAGES

Troubleshooting

15.1. Cannot See the IP Address, LAN Status LED Stays Red

Troubleshooting steps for when IP address is not visible and LAN LED is red.

15.2. IP Address is All Zeroes, LAN Status LED Stays Red

Steps for troubleshooting zero IP address and red LAN LED.

Cannot Communicate to the Power Supply

Cannot View Web Pages Over a Peer-to-Peer Network

Cannot Open Web using Laptop or Dual-LAN Card Computer

Web Page Refresh List Does Not Find Slave Supplies

Cannot Connect Using Hostname