TDSi DIGIgarde PLUS - Figure 4 Securing the Mount to the Mounting Surface

71 pages

Save Page as PDF

To Next Page

To Previous Page

Installation

DIGIgarde PLUS User Guide

Last Change Copyright

2012 TDSi

13 May, 2016 Page 11

4. Place the mounting plate on the wall and secure it in position with the

screws. Use a sprit level to ensure that the mounting plate is true.

Figure 4 Securing the mount to the mounting surface

5. Ensure that the anti-tamper magnet is in position below the cable access

hole.

Anti-tamper

magnet

Main Page

Table of Contents3
Introduction7
About this Manual8
Digigarde PLUS Layout8
Basic Concepts9
User Enrolment9
User Verification9
User ID Numbers9
Table 1 Single Factor Verification Modes10
Table 2 Two Factor Verification Modes11
Table 3 Three Factor Verification Modes11
Threshold12
Privilege Levels12
Table 4 Suggested Threshold Settings12
Log Definitions13
How to Use the Fingerprint Sensor13
Correct Positioning13
Incorrect Positioning13
Common Reasons for Enrolment Failure14
LED Indication14
Unpacking15
Fitting the Mounting Plate15
Figure 1 Removing the Security Screw from the Base15
Figure 2 Mark the Fixing and Cable Hole Positions16
Figure 3 Drilling the Holes: 6 MM for the Fixings and 8 MM for the Cable; Fit the Wall Plugs16
Figure 4 Securing the Mount to the Mounting Surface17
Figure 5 Feeding the Cable and Replacing the Reader18
Figure 6 Securing the Digigarde PLUS to the Mounting Plate18
Connecting Digigarde PLUS19
Preparing for Connection19
Figure 7 the Digigarde PLUS Cable Bundle19
Wiring Guide20
Table 5 Cable Assignments20
Power Connection21
Wiegand/Magnetic Clock Data to a Compatible ACU21
Alarm Connection22
Lock and Sensor Connection22
Figure 8 Alarm Connection22
Figure 9 Fail-Open or Fail-Locked Door Connections23
Communication24
Tcp/Ip24
Table 6 Ethernet RJ-45 Connector Pin Number (from Left to Right)24
Rs23225
Rs48525
Figure 10 Connecting a Single Digigarde PLUS to a PC Using RS-23225
Figure 11 Example of a Half-Duplex (2-Wire) RS-485 Network25
Power on26
Display Layout26
Check In/Check out26
First Tasks26
User Setup User Setup27
Setting up Admin Accounts28
Privilege Levels28
Setting up an Admin Account28
Enrolment30
Enrolling a Fingerprint31
Table 7 Possible Fingerprint Enrolment Errors32
Enrolling a Password33
Enrolling a Fingerprint and Password34
Card Enrolment34
► Enrol Fpcard35
Table 8 Card Enrolment Options35
Copy to Card36
Register FP Card36
Unregister FP Card36
Delete FP Card36
Copy Crd to Rdr36
Move Rdr to Crd36
The Options Menu37
Table 9 Options Menu Categories37
Device Settings38
Date/Time38
Language38
Date Format39
Daylight Saving Time40
Wiegand Format41
Advanced Options42
Table 10 Advanced Options42
Power Management43
Communication Options43
Table 11 Communication Options43
Log Options44
LED Mode44
Table 12 Log Options44
Standalone Mode Standalone Mode45
Figure 10 Access Control Options46
Figure 11 Example of Access Combination Use47
User Access Verification Flowchart48
Data out Type49
Standalone Mode49
The Access Control Menu49
Table 13 Access Options Menu49
Defining Time Patterns50
Assigning a Time Pattern to a Group51
Assigning a Time Pattern to a User51
User Access Options51
Selecting the User51
Assigning a User to a Group52
Setting a User's Time Patterns52
Table 14 User Access Options Menu52
Choosing a User's Verification Method53
Access Combinations53
Lock and Door Sense54
Table 15 Lock and Door Sense Settings54
Alarm55
Resetting the Alarm55
Defining Duress Options56
Table 16 Duress Options56
Anti Passback57
Connection57
Set up58
Use58
System Information59
System Information System Information59
Sys Info Menu59
Table 17 Sys Info Options59
Device Info Menu60
Free Space Info Menu60
Table 18 Device Info Settings60
Table 19 Free Space Info Settings60
Aintenance61
Cleaning the Keypad and Screen61
Cleaning the Optical Sensor61
Digigarde PLUS User Guide62
Troubleshooting63
How to Reset Language Back to English63
How to Reset the Unit63
How to Clear Admin Privileges63
When Fingerprint Verification Fails63
Communication Failures64
Display Shows "Please Try Again" When no Finger ID Presented for Verification64
Appendices App Endices65
Menu Structure65
Digigarde PLUS User Guide66
Digigarde PLUS User Guide67
Wiegand Format68
Table 20 Wiegand Pulse Characteristics68
26-Bit Wiegand Format69
Table 21 26-Bit Wiegand Field Definition69

TDSi DIGIgarde PLUS - Figure 4 Securing the Mount to the Mounting Surface

Table of Contents

Other manuals for TDSi DIGIgarde PLUS