FORMA: Service & Maintenance manual - rev. 3.0
Page ii
6.1.
T
HE DISPLAY DOES NOT ILLUMINATE
................................................................................................................ 6.2
6.2.
T
HE DISPLAY SHOWS
“SAFETY SWITCH”..................................................................................................... 6.6
6.3.
T
HE DISPLAY SHOWS
“E 3”............................................................................................................................... 6.7
6.3.1.
The inverter display shows E01, E02, E03, E04 or E05 ................................................................... 6.9
6.3.2.
The inverter display shows E06 or E07 .......................................................................................... 6.11
6.3.3.
The inverter display shows E08, E10, E11 or E22.......................................................................... 6.12
6.3.4.
The inverter display shows E09 ...................................................................................................... 6.13
6.3.5.
The inverter display shows E12 ...................................................................................................... 6.15
6.3.6.
The inverter display shows E14 ...................................................................................................... 6.17
6.3.7.
The inverter display shows E15 ...................................................................................................... 6.18
6.3.8.
The inverter display shows E21 ...................................................................................................... 6.20
6.3.9.
The inverter display does not show any error................................................................................. 6.21
6.4.
T
HE BELT MOTOR IS JERKING
.......................................................................................................................... 6.23
6.5.
T
HE BELT MOTOR STARTS WITH DELAY
.......................................................................................................... 6.24
6.6.
T
HE DISPLAYED SPEED IS INCORRECT
............................................................................................................. 6.25
6.7.
T
HE DISPLAY SHOWS
“E 5”............................................................................................................................. 6.28
6.8.
T
HE UP
-
DOWN MOVES IN ONLY ONE DIRECTION
.............................................................................................. 6.32
6.9.
T
HE DISPLAYED ELEVATION IS INCORRECT
..................................................................................................... 6.34
6.10.
T
HE FAN IS NOT WORKING
.............................................................................................................................. 6.36
6.11.
T
HERE IS NO HEART RATE SIGNAL
................................................................................................................... 6.39
6.12.
T
HE HEART RATE SIGNAL IS INCORRECT
......................................................................................................... 6.40
7.
DISASSEMBLY OF COMPONENTS ................................................................................................................. 7.1
7.1.
D
ISASSEMBLING THE DISPLAY
.......................................................................................................................... 7.1
7.2.
D
ISASSEMBLING THE
EPROM.......................................................................................................................... 7.2
7.3.
D
ISASSEMBLING THE DISPLAY BOARDS
............................................................................................................. 7.3
7.4.
D
ISASSEMBLING THE KEYBOARD
...................................................................................................................... 7.4
7.5.
D
ISASSEMBLING THE CARDIO RECEIVER
........................................................................................................... 7.5
7.6.
D
ISASSEMBLING THE SAFETY SWITCH
............................................................................................................... 7.6
7.7.
D
ISASSEMBLING THE MOTOR GUARD
................................................................................................................ 7.7
7.8.
D
ISASSEMBLING THE REAR ROLLER
.................................................................................................................. 7.8
7.9.
D
ISASSEMBLING THE MOTOR ROLLER AND DRIVE
-
BELT
.................................................................................. 7.10
7.10.
D
ISASSEMBLING THE TREAD
-
BELT AND RUNNING TRACK
................................................................................ 7.12
7.11.
D
ISASSEMBLING THE SHOCK ABSORBERS
....................................................................................................... 7.14
7.12.
D
ISASSEMBLING THE FOOTREST GUIDE
........................................................................................................... 7.15
7.13.
D
ISASSEMBLING THE SIDE GUARDS
................................................................................................................. 7.16
7.14.
D
ISASSEMBLING THE MOTOR GUARD GRILLE
.................................................................................................. 7.17
7.15.
D
ISASSEMBLING THE TREAD
-
BELT MOTOR
...................................................................................................... 7.18
7.16.
D
ISASSEMBLING THE ELECTRONIC CIRCUIT BOARDS
....................................................................................... 7.19
7.17.
S
MONTAGGIO SCHEDA INTERFACCIA VENTOLA
............................................................................................... 7.21
7.18.
D
ISASSEMBLING THE INVERTER
...................................................................................................................... 7.22
7.19.
D
ISASSEMBLING THE COLUMN AND RUBBER GUARD
....................................................................................... 7.23
7.20.
D
ISASSEMBLING THE UP
-
DOWN MOTOR
.......................................................................................................... 7.24
7.21.
D
ISASSEMBLING THE UP
-
DOWN FRAME
........................................................................................................... 7.25
7.22.
D
ISASSEMBLING THE HANDLEBARS
................................................................................................................ 7.26
8.
ADJUSTMENTS.................................................................................................................................................... 8.1
8.1.
T
ENSIONING A NEW TREAD
-
BELT
...................................................................................................................... 8.1
8.2.
T
ENSIONING A USED TREAD
-
BELT
..................................................................................................................... 8.2
8.3.
C
ENTERING THE TREAD
-
BELT
........................................................................................................................... 8.3
8.4.
A
LIGNING THE TREAD
-
BELT MOTOR DRIVE
-
BELT
.............................................................................................. 8.4
8.5.
T
ENSIONING THE TREAD
-
BELT MOTOR DRIVE BELT
........................................................................................... 8.5
8.6.
C
ALIBRATING THE TREAD
-
BELT SPEED
............................................................................................................. 8.6
8.7.
A
DJUSTING THE UP
-
DOWN MOTOR CURRENT LIMITER
....................................................................................... 8.7
9.
MACHINE CONFIGURATION .......................................................................................................................... 9.1
9.1.
LANGUAGE CONFIGURATION
............................................................................................................................. 9.1
9.2.
V
IEWING THE WORKING PARAMETERS
.............................................................................................................. 9.2
To Next Page
Loading...
