TECO F510 series - Page 39

3-26
 PUMP Wiring Diagram for Pressure Sensor of Current Type
Single Pump:
F510 Single Pump Operation
Operation Switch
Pressure
Converter
TM2
SW2
SW3
NPN
J
P
1
J
P
2
V
I
S(+)
S(-)
S1
S3 S5
AI2
E24VGS2S4S6F1F2POP I
24V
+10V
MT
GND GND
AI1
AO2 E
R1A R1B R1C R2A R2C R3A R3C
AO1
00-02=1 (Control Circuit Terminal)
04-00=1 (4mA~20mA); 10-00=0 (Target Source: Keypad)
10-01=2 (Feedback Source: AI2)
10-03=XXX1b (PID is enabled)
23-00=1(Pump); 23-01=0 (Single Pump)
Multi-Pump:
F510 Multi-Pump Operation: Master F510 Multi-Pump Operation: Follower 1
F510 Multi-Pump Operation: Follower 2 F510 Multi-Pump Operation: Follower 3
Operation
Switch
Pressur e
Converter
CON2
TM2
CON2
CON2
CON2
TM2
AB AB
AB AB
S(+) S(-) S1 S3 S5 AI2
E24VGS2S4S6F1F2POP I
24V +10V MT GND GND AI1
AO2 E
R1A R1B R1C R2A R2C R3A R3C
AO1
S(+) S(-) S1 S3 S5 AI2
E24VGS2S4S6F1F2POP I
24V +10V MT GND GND AI1
AO2 E
R1A R1B R1C R2A R2C R3A R3C
AO1
S(+) S(-) S1 S3 S5 AI2
E24VGS2S4S6F1F2POP I
24V +10V MT GND GND AI1
AO2 E
R1A R1B R1C R2A R2C R3A R3C
AO1
TM2
TM2
S(+) S(-) S1 S3 S5 AI2
E24VGS2S4S6F1F2POP I
24V +10V MT GND GND AI1
AO2 E
R1A R1B R1C R2A R2C R3A R3C
AO1
00-02=1 (Control Circuit Terminal); 04-00=1 (4~20mA)
10-00=0 (Target Source: Keypad); 10-01=2 (Feedback Source: AI2）
10-03=XXX1b (PID is enabled); 23-00=1(Pump); 23-01=1 (Master)
00-02=1 (Control Circuit Terminal); 04-00=0 (0~10V)
10-00=0 (Target Source: Keypad); 10-01=2 (Feedback Source: AI2）
10-03=XXX1b (PID is enabled); 23-00=1(Pump); 23-01=2 (Follower 1)
00-02=1 (Control Circuit Terminal); 04-00=0 (0~10V)
10-00=0 (Target Source: Keypad); 10-01=2 (Feedback Source: AI2）
10-03=XXX1b (PID is enabled); 23-00=1(Pump); 23-01=3 (Follower 2)
00-02=1 (Control Circuit Terminal); 04-00=0 (0~10V)
10-00=0 (Target Source: Keypad); 10-01=2 (Feedback Source: AI2）
10-03=XXX1b (PID is enabled); 23-00=1(Pump);
23-01=4 (Follower 3)
SW2
SW3
NPN
J
P
1
J
P
2
V
I
Notes: 1. The position of dip switch requires being correct (SW2, SW3).
2. It is required to reconnect after setting Master/ Slave.
3. 24VG and GND require short circuit.