THOMSON RD1000 User Manual

RD1000 / RD1002
Receiver Descrambler
User Manual
(Release 7.3.1)
Edition 2
www.thomson-networks.com
This document and any updates and/or supplemental information,
including any copies thereof, cannot be reproduced, neither
communicated to a third party, without written authorization from
THOMSON.
 2010
THOMSON
All rights
reserved

THOMSON RD1000 Specifications

General

Type	Receiver
Supported Bands	FM
Frequency Range	FM: 87.5 - 108 MHz, AM: 522 - 1620 kHz
Power Supply	230V AC, 50Hz
Audio Output	3.5 mm jack

Summary

Section 1 – Getting Started

1.1 Installation

Provides instructions for installing the unit, including cooling, rack information, and rack mounting steps.

1.2 Quick Start Guide

Outlines the basic steps to get the unit operational, guiding users to Section 4 for detailed setup.

Section 2 – Controls and Configuration

2.1 Front of Unit

Details the physical front panel of the unit, showing input and error indicators.

2.2 Rear of Unit

Describes the physical rear panel of the unit, highlighting its various input/output connectors.

2.3 Front Panel Display Layout

Illustrates a typical front panel screen, explaining key elements like screen title and cursor.

2.4 Front Panel Indicators

Explains the front panel LEDs (INPUT, ERROR) and their relation to unit status and errors.

Section 3 – Option Cards Overview

3.1 8VSB/QAM Receiver – Option NRD00HCSAA

Describes the 8VSB/QAM receiver card for tuning channels and demodulating RF inputs.

3.2 Serial Transport Stream I/O (DVB-ASI/SMPTE 310M) – Option NRD00H02AA

3.4 Dual Input COFDM Receiver – Option NRD00H04AA

3.5 Quad Input DVB-S/DVB-S2 with LNB – Option NRD00H12AB

3.6 CAM Decryption – Basic feature

3.7 Dual MPEG over IP Input/ UDP Output – Option NRD00H05AA

3.8 Advanced Satellite Features – Option NRD00S02AA

Section 4 – Using the Front Panel to Configure the unit

4.1 Input Option – Active Input and Backup Configuration Selection

Guides on selecting the active input and configuring backup input settings for redundancy.

4.2 8VSB/QAM Receiver Configuration

Details the configuration steps for the 8VSB/QAM receiver input card, including channel and modulation.

4.3 Serial Transport Stream Input/Output Configuration

Explains how to configure the serial TS input/output card, including input type selection.

4.4 GPIO Module Configuration

4.5 Dual Input COFDM Receiver Configuration

Details configuration for the dual COFDM receiver, covering source selection and signal parameters.

4.6 Quad Input DVB-S/DVB-S2 Receiver Configuration

Guides on configuring the DVB-S/S2 receiver, including source selection and satellite parameters.

4.7 CA Decryption Setup

Explains how to set up CAM decryption, including CAM operation modes and PID selection.

4.8 Dual MPEG over IP Input/ UDP Output Configuration

Details network configuration for the MPEG/IP card, including IP address, gateway, and port settings.

4.11 Network Setup

Guides on configuring static IP addresses or using DHCP for network connectivity.

4.12 Panel Lock Configuration

Details how to lock and unlock the front panel using a user-defined password.

4.13 SNMP Configuration

Explains how to configure SNMP settings, including RO and RW communities for trap reporting.

4.14 SMPTE 333M Configuration

4.16 Feature Licensing

Section 5 – Using the Web Client to Configure the unit

5.1 Login to Web Client

Provides steps to log into the unit's remote web client using administrator or user credentials.

5.2 Status Indicators

5.3 Input Configuration

Guides on setting the desired input as active and configuring specific input card options.

5.5 Profiles Management

5.7 Reset Unit