Unipulse F381A - Page 124

115
5 COMMUNICATIONS
115
COMMUNICATIONS
Chapter
5
(transmission to the F381A) Input range (display range)
0010
4
10
3
10
2
10
1
10
0
Delimiter
(CR,CR+LF)
-10000 to 10000
0000010
1
10
0
Delimiter
(CR,CR+LF)
Y-axis Start Point +
0: 25 1: 50 2: 100 3: 200
4: 300 5: 400 6: 500 7: 1000
8: 2000 9: 3000 10: 4000
11: 5000 12: 10000 13: 20000
00010
3
10
2
10
1
10
0
Delimiter
(CR,CR+LF)
Time or displacement (Front)
0 to 2000 (× Measurement Length/2000)
Displacement (Back)
-2000 to 0 (× Measurement Length/2000 )
0000010
1
10
0
Delimiter
(CR,CR+LF)
Time or displacement (Front)
X-axis Start Point +
0: 25 1: 50 2: 100 3: 200 4: 400
5: 600 6: 800 7: 1000 8: 1200 9: 1400
10: 1600 11: 1800 12: 2000 13: 2200
(× Measurement Length/2000)
Displacement (Back)
X-axis Start Point +
0: -25 1: -50 2: -100 3: -200 4: -400
5: -600 6: -800 7: -1000 8: -1200 9: -1400
10: -1600 11: -1800 12: -2000 13: -2200
(× Measurement Length/2000)
00000010
0
Delimiter
(CR,CR+LF)
0: External Input 1: Setting
（0 can be set only
when the time or displacement (Front))
00000010
0
Delimiter
(CR,CR+LF)
1 to 5
00000010
0
Delimiter
(CR,CR+LF)
0: Sct1 1: Sct2 2: Sct3
3: Sct4 4: Sct5
00000010
0
Delimiter
(CR,CR+LF)
0: Always 1: Sample 2: Peak
3: Bottom 4: Peak to Peak
5: Relative Maximum 6: Relative Minimum
7: Inflection Point 8: Average
9: End Displacement
00010
3
10
2
10
1
10
0
Delimiter
(CR,CR+LF)
Time or displacement (Front)
0 to 2047 (× Measurement Length/2000)
* However, End point of the previous section
≦Start point≦End point
Displacement (Back)
-2047 to 0 (× Measurement Length/2000)
* However, End point of the previous section
≧Start point≧End point
00010
3
10
2
10
1
10
0
Delimiter
(CR,CR+LF)
Time or displacement (Front)
0 to 2047 (× Measurement Length/2000)
* However, Start point≦End point
≦Start point of the next section
Displacement (Back)
-2047 to 0 (× Measurement Length/2000)
* However, Start point≧End point
≧Start point of the next section
00010
3
10
2
10
1
10
0
Delimiter
(CR,CR+LF)
-9999 to +9999
* Setting HI limit < LO limit is unacceptable.
00010
3
10
2
10
1
10
0
Delimiter
(CR,CR+LF)
-9999 to +9999
* Setting HI limit < LO limit is unacceptable.