Name: WEIHONG 200 Series
Brand: WEIHONG
Rating: 4 (1 reviews)

To Next Page

To Previous Page

上海维宏电子科技股份有限公司

Weihong Electronic Technology Co., Ltd.

Specialized, Concentrated, Focused - 27 -

3 Manipulation

3.1 DEBUGGING STEPS .................................................................................................................................... - 29 -

3.2 ADJUSTMENT OF AXIAL DIRECTION AND PULSE EQUIVALENT ............................................................................. - 30 -

3.2.1 Axial Direction Adjustment .............................................................................................................. - 30 -

3.2.2 Pulse Equivalent Adjustment ........................................................................................................... - 30 -

3.2.3 Upper & Lower Limit Setting of Workbench Stroke.......................................................................... - 32 -

3.3 RETURNING TO MACHINE ORIGIN ................................................................................................................ - 34 -

3.3.1 Principle of Motion of Returning to Machine Origin ........................................................................ - 34 -

3.3.2 Parameters Specifications ................................................................................................................ - 37 -

3.3.3 FAQ & Troubleshooting .................................................................................................................... - 38 -

3.4 SPINDLE PARAMETERS ADJUSTMENT ............................................................................................................. - 40 -

3.5 PORT POLARITY ADJUSTMENT ..................................................................................................................... - 42 -

3.6 TOOL MEASUREMENT ................................................................................................................................ - 44 -

3.6.1 Software Interface ........................................................................................................................... - 44 -

3.6.2 Mobile Calibration ........................................................................................................................... - 45 -

3.6.3 Fixed Calibration .............................................................................................................................. - 46 -

3.6.4 First Calibration/ Tool Calibration after Tool Change....................................................................... - 47 -

3.7 OFFSET SETTING ....................................................................................................................................... - 49 -

3.7.1 WCS (Workpiece Coordinate System) .............................................................................................. - 49 -

3.7.2 Extended WCS .................................................................................................................................. - 50 -

3.7.3 Software Interface ........................................................................................................................... - 50 -

3.8 CENTERING .............................................................................................................................................. - 53 -

3.9 ADJUSTMENT OF VELOCITY & ACCELERATION ................................................................................................. - 54 -

3.9.1 Feedrate Setting ............................................................................................................................... - 54 -

3.9.2 Traverse Speed Setting (G00 Speed Setting) .................................................................................... - 54 -

3.9.3 Parameters Specification ................................................................................................................. - 54 -

3.10 SIMULATION & TRACK ............................................................................................................................... - 57 -

3.10.1 Simulation .................................................................................................................................... - 57 -

3.10.2 Motion Trace................................................................................................................................ - 58 -

3.11 COMPENSATION ....................................................................................................................................... - 59 -

3.11.1 Screw Error Compensation .......................................................................................................... - 59 -

3.11.2 Tool Compensation ...................................................................................................................... - 63 -

3.11.3 Across Quadrant Error (AQE) Compensation ............................................................................... - 65 -

3.12 LOG AND DIAGNOSIS ................................................................................................................................. - 67 -

3.12.1 Log ............................................................................................................................................... - 67 -

3.13 PROGRAM FILE MANAGEMENT.................................................................................................................... - 68 -

3.13.1 Program Wizard .......................................................................................................................... - 68 -

3.13.2 Part Statistic ................................................................................................................................ - 69 -

3.13.3 Program File ................................................................................................................................ - 69 -

3.14 HANDWHEEL OPERATION ........................................................................................................................... - 75 -

3.14.1 Handwheel Mode ........................................................................................................................ - 75 -

3.14.2 Handwheel Guide ........................................................................................................................ - 75 -

3.15 SYSTEM MANAGEMENT ............................................................................................................................. - 77 -

Brand	WEIHONG
Model	200 Series
Category	Control Systems
Language	English

WEIHONG 200 Series Manufacturer's Manual

Table of Contents

Other manuals for WEIHONG 200 Series

Questions and Answers:

WEIHONG 200 Series Specifications

Related product manuals