EasyManuals Logo

WEIHONG 200 Series Manufacturer's Manual

Default Icon
158 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #8 background imageLoading...
Page #8 background image
上海维宏电子科技股份有限公司
Weihong Electronic Technology Co., Ltd.
- 2 - Specialized, Concentrated, Focused
3.7.1 WCS (Workpiece Coordinate System) .............................................................................................. - 49 -
3.7.2 Extended WCS .................................................................................................................................. - 50 -
3.7.3 Software Interface ........................................................................................................................... - 50 -
3.8 CENTERING .............................................................................................................................................. - 53 -
3.9 ADJUSTMENT OF VELOCITY & ACCELERATION ................................................................................................. - 54 -
3.9.1 Feedrate Setting ............................................................................................................................... - 54 -
3.9.2 Traverse Speed Setting (G00 Speed Setting) .................................................................................... - 54 -
3.9.3 Parameters Specification ................................................................................................................. - 54 -
3.10 SIMULATION & TRACK ............................................................................................................................... - 57 -
3.10.1 Simulation .................................................................................................................................... - 57 -
3.10.2 Motion Trace................................................................................................................................ - 58 -
3.11 COMPENSATION ....................................................................................................................................... - 59 -
3.11.1 Screw Error Compensation .......................................................................................................... - 59 -
3.11.2 Tool Compensation ...................................................................................................................... - 63 -
3.11.3 Across Quadrant Error (AQE) Compensation ............................................................................... - 65 -
3.12 LOG AND DIAGNOSIS ................................................................................................................................. - 67 -
3.12.1 Log ............................................................................................................................................... - 67 -
3.13 PROGRAM FILE MANAGEMENT.................................................................................................................... - 68 -
3.13.1 Program Wizard .......................................................................................................................... - 68 -
3.13.2 Part Statistic ................................................................................................................................ - 69 -
3.13.3 Program File ................................................................................................................................ - 69 -
3.14 HANDWHEEL OPERATION ........................................................................................................................... - 75 -
3.14.1 Handwheel Mode ........................................................................................................................ - 75 -
3.14.2 Handwheel Guide ........................................................................................................................ - 75 -
3.15 SYSTEM MANAGEMENT ............................................................................................................................. - 77 -
3.15.1 System Info .................................................................................................................................. - 77 -
3.15.2 Network Connection .................................................................................................................... - 77 -
3.15.3 Language ..................................................................................................................................... - 77 -
3.15.4 Register ........................................................................................................................................ - 77 -
3.16 NETWORK CONNECTION AND SHARE ............................................................................................................ - 79 -
3.16.1 IP Setup ........................................................................................................................................ - 79 -
3.16.1.1 Direct Connection or Switch Connection................................................................................................... - 79 -
3.16.1.2 Router Connection .................................................................................................................................... - 82 -
3.16.1.3 Multiple NK280 Connection ...................................................................................................................... - 83 -
3.16.2 Connection Verification Setup ..................................................................................................... - 83 -
3.16.3 NK280 Network Files Management by PC via FTP....................................................................... - 84 -
3.16.4 NK280 Network Files Management by PC via Network Sharing ................................................. - 84 -
3.17 AUXILIARY FUNCTION ................................................................................................................................ - 86 -
3.17.1 Single Block .................................................................................................................................. - 86 -
3.17.2 Start Line (Selective Processing) .................................................................................................. - 86 -
3.17.3 Breakpoint Resume ...................................................................................................................... - 86 -
3.17.4 Parameter Auto Backup ............................................................................................................... - 86 -
3.17.5 User Code Input (MDI) ................................................................................................................. - 87 -
3.17.6 Coordinate Backup ...................................................................................................................... - 87 -
3.18 TOOL MAGAZINE ...................................................................................................................................... - 90 -

Table of Contents

Other manuals for WEIHONG 200 Series

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the WEIHONG 200 Series and is the answer not in the manual?

WEIHONG 200 Series Specifications

General IconGeneral
BrandWEIHONG
Model200 Series
CategoryControl Systems
LanguageEnglish

Related product manuals