Xerox WorkCentre 4150

January 2016
2-33
WorkCentre 4150/4250/4260WorkCentre WorkCentre 4150/4250/42604150/
05-500
Status Indicator RAPs
05-500 DADF Jam 5 RAP
05-500 (4150) The machine has detected that the DADF, DADF top cover assembly or exit
assembly are open during run.
05-500 (4260) The machine has detected that the DADF or DADF top cover assembly are
open during run.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Go to the relevant procedure:
• 4150 Checkout
• 4250/4260 Checkout
• 4265 Checkout
4150 Checkout
Refer to Wiring Diagram 9 and Wiring Diagram 11. Perform the following:
1. Open the DADF top cover assembly, PL 5.15 Item 11. Remove all jammed paper.
2. Raise the DADF input tray, PL 5.10 Item 5. Remove all jammed paper.
3. Open the DADF. Check that the platen cover sensor actuator, PL 14.10 Item 12 moves
freely and is not damaged.
4. Enter dC330 code 05-400. Check the platen cover sensor (Q05-400), PL 14.10 Item 14.
5. Check the wiring between the platen cover sensor and CN3 on the Scanner PWB. If nec-
essary, install a new platen cover sensor, PL 14.10 Item 14.
6. Open the DADF top cover assembly, PL 5.15 Item 11. Check that the door open switch
actuator is not damaged.
7. Enter dC330 code 05-160. Check the DADF door open switch (S05-160), PL 5.25 Item 8.
8. Check the wiring between the DADF door open switch and CN6 on the DADF PWB. If
necessary, install a new DADF door open switch, PL 5.25 Item 8.
9. Open the exit assembly, PL 5.20 Item 26. Check that the exit open sensor actuator is not
damaged.
10. Enter dC330 code 05-180. Check the exit open sensor (Q05-180), PL 5.20 Item 16.
11. Check the wiring between the exit open sensor and CN6 on the DADF Sensor PWB. If
necessary, install a new exit open sensor, PL 5.20 Item 16.
12. Check the wiring between CN1 on the DADF Sensor PWB and CN3 on the DADF PWB.
13. If necessary, install new components:
• DADF PWB, PL 5.20 Item 6.
• DADF sensor PWB, PL 5.20 Item 4.
• Document transport assembly, PL 5.10 Item 2.
• Scanner assembly, PL 14.10 Item 1.
4250/4260 Checkout
Refer to Wiring Diagram 28 and Wiring Diagram 29. Perform the following:
1. Open the DADF top cover assembly, PL 5.30 Item 2. Remove all jammed paper.
2. Open the DADF. Check that the platen cover sensor actuator, PL 14.13 Item 27 moves
freely and is not damaged.
3. Enter dC330 code 05-400. Check the platen cover sensor (Q05-400), PL 14.13 Item 14.
4. Check the wiring between the platen cover sensor and CN4 on the Scanner PWB. If nec-
essary, install a new platen cover sensor, PL 14.13 Item 14.
5. Open the DADF top cover assembly, PL 5.30 Item 2. Check that the door open switch
actuator is not damaged. If necessary, install a new DADF top cover assembly, PL 5.30
Item 2.
6. Enter dC330 code 05-160. Check the DADF door open switch (S05-160), PL 5.50 Item
21.
7. Check the wiring between the DADF door open switch and CN4 on the DADF PWB. If
necessary, install a new document transport assembly, PL 5.30 Item 26.
8. If necessary, install new components:
• DADF PWB, PL 5.30 Item 24.
• Document transport assembly, PL 5.30 Item 26.
• Scanner assembly, PL 14.13 Item 1.
4265 Checkout
Refer to Wiring Diagram 44 and Wiring Diagram 45. Perform the following:
1. Open the DADF top cover assembly, PL 5.60. Remove all jammed paper.
2. Open the DADF. Check that the platen cover sensor actuator, PL 14.13 Item 27 moves
freely and is not damaged.
3. Enter dC330 code 05-400. Check the platen cover sensor (Q05-400), PL 14.13 Item 14.
4. Check the wiring between the platen cover sensor and CN4 on the Scanner PWB. If nec-
essary, install a new platen cover sensor, PL 14.13 Item 14.
5. Open the DADF top cover assembly, Check that the door open sensor actuator is not
damaged. If necessary, install a new DADF top cover assembly, PL 5.30 Item 2.
6. Enter dC330 code 05-160. Check the DADF door open sensor, PL 5.65.
7. Check the wiring between the DADF door open sensor PL 5.65 and CN6 on the DADF
PWB. If necessary, install a new document transport assembly, PL 5.60.
8. If necessary, install new components:
• DADF PWB, PL TBD.
• Document transport assembly, PL 5.60.
• Scanner assembly, PL 14.13 Item 1.