January 2016
2-44
WorkCentre WorkCentre 4150/4250/4260WorkCentre 4150/4250/42604150/
07-120, 07-130
Status Indicator RAPs
07-120 Tray 1 Cassette Out RAP
07-120 The machine has detected that tray 1 is not home.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
NOTE: The main PWB has test points. The location of the test points is shown on the following
PJ location illustrations:
• 4150 Main PWB.
• 4250/4260 Main PWB.
• 4265 Main PWB.
Refer to:
• (4150) Wiring Diagram 6.
• (4250/4260) Wiring Diagram 24 and Wiring Diagram 25.
• (4265) Wiring Diagram 40 and Wiring Diagram 41.
Perform the following:
1. Make sure tray 1 is fully home.
2. Pull out tray 1. Check for obstructions behind the tray.
3. Check that the tray 1 home position sensor actuator on the back of the tray is not missing
or damaged.
4. Enter dC330 code 07-100. Check the tray 1 home position sensor (Q07-100), PL 7.15
Item 2.
5. (4150) Check the wiring between the tray 1 home position sensor and CN15 on the Main
PWB. If necessary, install a new tray 1 home position sensor, PL 7.15 Item 2.
6. (4250/4260) Check the wiring between the tray 1 home position sensor and CN15 on the
Main PWB. If necessary, install a new tray 1 home position sensor, PL 7.15 Item 2.
7. (4265) Check the wiring between the tray 1 home position sensor and CN29 on the Main
PWB. If necessary, install a new tray 1 home position sensor, PL 7.15 Item 2.
8. Manually lower, then raise the tray 1 feed head link arm, PL 7.17 Item 12. Check that the
feed head, PL 8.10 Item 5 moves freely. Check that the actuator on the feed head actu-
ates the tray 1 up limit switch, PL 8.10 Item 17.
9. Check the tray 1 up limit switch, PL 8.10 Item 17.
NOTE: There is not a component control code for the tray 1 up limit switch.
10. (4150) Check the wiring between the tray 1 up limit switch and CN19 on the Main PWB.
11. (4250/4260) Check the wiring between the tray 1 up limit switch and CN15 on the Main
PWB.
12. (4265) Check the wiring between the tray 1 up limit switch and CN19 on the Main PWB.
13. If necessary, install a new tray 1 feed assembly, PL 8.10 Item 1.
14. Perform the OF5
Main PWB Check RAP.
07-130 Jam 0 From Tray 1 RAP
07-130 The lead edge of the paper failed to actuate the registration sensor within the correct
time after paper was fed from tray 1.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
NOTE: The main PWB has test points. The location of the test points is shown on the following
PJ location illustrations:
• 4150 Main PWB.
• 4250/4260 Main PWB.
• 4265 Main PWB.
NOTE: The side cover assembly interlock switch must be closed to supply +24V to the motors
and clutches.
Refer to:
• (4150) Wiring Diagram 4 and Wiring Diagram 5.
• (4250/4260) Wiring Diagram 24.
• (4265) Wiring Diagram 40.
Perform the following:
1. Pull out tray 1. Remove all jammed paper.
2. Check the paper path for damage or obstructions.
3. Check that the registration sensor actuator, PL 8.15 Item 5 moves freely and is not dam-
aged. If necessary, install a new registration sensor actuator assembly, PL 8.15 Item 14.
4. Enter dC330 code 08-500. Check the registration sensor (Q08-500), PL 8.15 Item 8.
5. (4150) Check the wiring between the registration sensor and CN13 on the Main PWB. If
necessary, install a new registration sensor, PL 8.15 Item 8.
6. (4250/4260) Check the wiring between the registration sensor and CN12 on the Main
PWB. If necessary, install a new registration sensor, PL 8.15 Item 8.
7. (4265) Check the wiring between the registration sensor and CN27 on the Main PWB. If
necessary, install a new registration sensor, PL 8.15 Item 8.
8. Check that the feed sensor actuator, PL 8.15 Item 4 moves freely and is not damaged. If
necessary, install a new feed sensor actuator assembly, PL 8.15 Item 13.
9. Enter dC330 code 08-100. Check the feed sensor (Q08-100), PL 8.15 Item 8.
10. (4150) Check the wiring between the feed sensor and CN13 on the Main PWB. If neces-
sary, install a new feed sensor, PL 8.15 Item 8.
11. (4250/4260) Check the wiring between the feed sensor and CN12 on the Main PWB. If
necessary, install a new feed sensor, PL 8.15 Item 8.
12. (4265) Check the wiring between the feed sensor and CN27 on the Main PWB. If neces-
sary, install a new feed sensor, PL 8.15 Item 8.
13. Enter dC330 code 04-100 to run the main BLDC motor.
14. While the main BLDC motor runs, stack the code 08-810 to energize the tray 1 pickup
clutch (CL08-810). Check that the tray 1 feed roll, PL 8.10 Item 12 rotates.
To Next Page
Loading...
