Xerox WorkCentre 4150

January 2016
2-45
WorkCentre WorkCentre 4150/4250/4260WorkCentre 4150/4250/42604150/
07-130, 07-200, 300, 400
Status Indicator RAPs
15. (4150) Check the wiring between the tray 1 pickup clutch and CN13 on the Main PWB.
Install new components as necessary, PL 4.20, PL 7.15 and PL 8.10.
16. (4250/4260) Check the wiring between the tray 1 pickup clutch and CN12 on the Main
PWB. Install new components as necessary, PL 4.25, PL 7.15 and PL 8.10.
17. (4265) Check the wiring between the tray 1 pickup clutch and CN27 on the Main PWB.
Install new components as necessary, PL 4.25, PL 7.15 and PL 8.10.
18. While the main BLDC motor runs, stack the code 08-850 to energize the registration
clutch (CL08-850). Check that the registration roll, PL 4.15 Item 1 rotates.
19. While the main BLDC motor runs, stack the code 08-850 to energize the registration
clutch (CL08-850). Check that the registration roll, PL 4.15 Item 1 rotates.
20. (4150) Check the wiring between the registration clutch and CN13 on the Main PWB.
Install new components as necessary, PL 4.15 and PL 4.20.
21. (4250/4260) Check the wiring between the registration clutch and CN12 on the Main
PWB. Install new components as necessary, PL 4.15 and PL 4.25.
22. (4265) Check the wiring between the registration clutch and CN27 on the Main PWB.
Install new components as necessary, PL 4.15 and PL 4.25.
23. Check that the following components are clean and rotate freely, install new components
as necessary:
• Tray 1 feed roll, PL 8.10 Item 12.
• Tray 1 nudger roll, PL 8.10 Item 12.
• Tray 1 retard roll, PL 7.15 Item 20.
• Registration roll, PL 4.15 Item 1.
• Registration roll idler, PL 4.15 Item 7.
24. If necessary, install a new tray feed assembly, PL 8.10 Item 1.
25. Perform the OF5 Main PWB Check RAP.
07-200, 300, 400 Tray 2, 3, 4 or HCF Paper Low RAP
07-200 The machine has detected that tray 2 is nearly empty when the tray is full.
07-300 The machine has detected that tray 3 or HCF is nearly empty when the tray is full.
07-400 The machine has detected that tray 4 is nearly empty when the tray is full.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Go to the relevant procedure:
• 4150 and 4250/42604265 Without an HCF
• 4250/4260/4265 With an HCF
4150 and 4250/42604265 Without an HCF
NOTE: Trays 2, 3 and 4 are identical. Check the relevant tray module.
Refer to:
• (4150) Wiring Diagram 7, Wiring Diagram 12 and Wiring Diagram 13.
• (4250/4260) Wiring Diagram 12, Wiring Diagram 13 and Wiring Diagram 26.
• (4265) Wiring Diagram 12, Wiring Diagram 13 and Wiring Diagram 42.
Perform the following:
1. Make sure the tray is fully home.
2. Pull out the tray. Check for obstructions behind the tray.
3. Check the tray elevator mechanism on the back of the tray.
4. Check that the paper low sensor actuator on the tray elevator gear, PL 7.10 Item 24 is not
missing or damaged.
5. Replace the tray. Listen for the tray elevating motor to raise the knock-up plate. If the plate
does not rise, check the wiring between the tray elevating motor and CN7 on the Tray
PWB. If necessary, install new components:
• Tray elevating motor, PL 7.20 Item 7.
• Tray feed assembly, PL 8.10 Item 1.
6. Enter dC330. Check the relevant paper low sensor, PL 7.20 Item 3:
• Tray 2. Code 07-260.
• Tray 3. Code 07-360.
• Tray 4. Code 07-460.
7. Check the wiring between the paper low sensor and CN5 on the Tray PWB. If necessary,
install a new paper low sensor, PL 7.20 Item 3.
8. (4150) Check the wiring between CN1 on the Tray PWB and CN24 on the Main PWB.
9. (4150) Check the wiring between CN1 on the Tray PWB and CN24 on the Main PWB.
10. (4265) Check the wiring between CN1 on the Tray PWB and CN34 on the Main PWB.
11. If necessary, install new components:
• Tray PWB, PL 7.20 Item 6.
• Tray cassette, PL 7.10 Item 1.