Xerox WorkCentre 4150

January 2016
2-46
WorkCentre WorkCentre 4150/4250/4260WorkCentre 4150/4250/42604150/
07-200, 300, 400, 07-210, 310, 410
Status Indicator RAPs
12. Perform the OF5 Main PWB Check RAP.
4250/4260/4265 With an HCF
Refer to Wiring Diagram 30 and Wiring Diagram 31. Perform the following:
1. Make sure tray HCF tray is fully home.
2. Pull out the HCF tray. Check for obstructions behind the tray.
3. Check the tray elevator mechanism on the back of the tray.
NOTE: To remove the HCF tray, refer to REP 7.5.
4. Check that the HCF paper level sensor actuator, PL 7.55 Item 9 is not damaged.
5. Replace the HCF tray. Listen for the tray elevating motor to raise the knock-up plate. If the
plate does not rise, check the wiring between the tray elevating motor and CN7 on the
HCF PWB. If necessary, install new components:
• Tray elevating motor, PL 7.60 Item 10.
• Tray feed assembly, PL 8.10 Item 1.
6. Enter dC330 code 07-360. Check the paper low sensor (Q07-360), PL 7.60 Item 1.
7. Check the wiring between the upper paper low sensor and CN3 on the HCF PWB. If nec-
essary, install a new paper low sensor, PL 7.60 Item 1.
8. If necessary, install a new HCF PWB, PL 7.60 Item 7.
07-210, 310, 410 Paper Empty at Tray 2, 3, 4 or HCF RAP
07-210 The machine has detected that tray 2 is empty when the tray is full.
07-310 The machine has detected that tray 3 or HCF is empty when the tray is full.
07-410 The machine has detected that tray 4 is empty when the tray is full.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Go to the relevant procedure:
• 4150 and 4250/4260/4265 Without an HCF
• 4250/4260/4265 With an HCF
4150 and 4250/4260/4265 Without an HCF
NOTE: Trays 2, 3 and 4 are identical. Check the relevant tray module.
Refer to:
• (4150) Wiring Diagram 7, Wiring Diagram 12 and Wiring Diagram 13.
• (4260) Wiring Diagram 12, Wiring Diagram 13 and Wiring Diagram 26.
• (4265) Wiring Diagram 12, Wiring Diagram 13 and Wiring Diagram 42.
Perform the following:
1. Pull out the tray. Check that the paper empty actuator, PL 8.10 Item 4 moves freely and is
not damaged.
2. Replace the tray. Listen for the tray elevating motor to raise the knock-up plate. If the plate
does not rise, check the wiring between the tray elevating motor and CN7 on the Tray
PWB. If necessary, install new components:
• Tray elevating motor, PL 7.20 Item 7.
• Tray feed assembly, PL 8.10 Item 1.
3. Enter dC330. Check the relevant paper empty sensor, PL 8.10 Item 2:
• Tray 2. Code 07-210.
• Tray 3. Code 07-310.
• Tray 4. Code 07-410.
4. Check the wiring between the paper empty sensor and CN7 on the Tray PWB. If neces-
sary, install a new paper empty sensor, PL 8.10 Item 2.
5. (4150) Check the wiring between CN1 on the Tray PWB and CN24 on the Main PWB.
6. (4260) Check the wiring between CN1 on the Tray PWB and CN19 on the Main PWB.
7. (4265) Check the wiring between CN1 on the Tray PWB and CN34 on the Main PWB.
8. If necessary, install a new tray PWB, PL 7.20 Item 6.
9. Perform the OF5 Main PWB Check RAP.
4250/4260/4265 With an HCF
Refer to Wiring Diagram 31. Perform the following:
1. Pull out the HCF tray. Check that the HCF paper empty sensor actuator, PL 8.10 Item 4
moves freely and is not damaged.