Xerox WorkCentre 4150

January 2016
2-47
WorkCentre WorkCentre 4150/4250/4260WorkCentre 4150/4250/42604150/
07-210, 310, 410, 07-220, 320, 420
Status Indicator RAPs
2. Replace the HCF tray. Listen for the tray elevating motor to raise the knock-up plate. If the
plate does not rise, check the wiring between the tray elevating motor and CN7 on the
HCF PWB. If necessary, install new components:
• Tray elevating motor, PL 7.60 Item 10.
• Tray feed assembly, PL 8.10 Item 1.
3. Enter dC330 code 07-310. Check the HCF paper empty sensor (Q07-310), PL 8.10 Item
2.
4. Check the wiring between the HCF paper empty sensor and CN7 on the HCF PWB. If
necessary, install a new HCF paper empty sensor, PL 8.10 Item 2.
5. If necessary, install a new HCF PWB, PL 7.60 Item 7.
07-220, 320, 420 Tray 2, 3, 4 or HCF Cassette Out RAP
07-220 The machine has detected that tray 2 is not home.
07-320 The machine has detected that tray 3 or HCF is not home.
07-420 The machine has detected that tray 4 is not home.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
Go to the relevant procedure:
• 4150 and 4250/4260/4265 Without an HCF
• 4250/4260/4265 With an HCF
4150 and 4250/4260/4265 Without an HCF
NOTE: Trays 2, 3 and 4 are identical. Check the relevant tray module.
Refer to:
• (4150) Wiring Diagram 7, Wiring Diagram 12 and Wiring Diagram 13.
• (4250/4260) Wiring Diagram 12, Wiring Diagram 13 and Wiring Diagram 26.
• (4265) Wiring Diagram 12, Wiring Diagram 13 and Wiring Diagram 42.
Perform the following:
1. Make sure that the tray is fully home.
2. Pull out the tray. Check for obstructions behind the tray.
3. Check that the tray home position sensor actuator on the back of the tray is not missing or
damaged.
4. Enter dC330. Check the relevant tray home position sensor, PL 7.20 Item 3:
• Tray 2. Code 07-200.
• Tray 3. Code 07-300.
• Tray 4. Code 07-400.
5. Check the wiring between the tray home position sensor and CN6 on the Tray PWB. If
necessary, install a new tray home position sensor, PL 7.20 Item 3.
6. (4150) Check the wiring between CN1 on the Tray PWB and CN24 on the Main PWB.
7. (4250/4260) Check the wiring between CN1 on the Tray PWB and CN19 on the Main
PWB.
8. (4256) Check the wiring between CN1 on the Tray PWB and CN34 on the Main PWB.
9. Manually lower, then raise the tray feed head link arm, PL 7.25 Item 13. Check that the
feed head, PL 8.10 Item 5 moves freely. Check that the actuator on the feed head actu-
ates the tray up limit switch, PL 8.10 Item 17.
10. Check the tray up limit switch, PL 8.10 Item 17.
NOTE: There is not a component control code for the tray up limit switch.
11. Check the wiring between the tray up limit switch and CN7 on the Tray PWB.
12. Install new components as necessary: