Xerox WorkCentre 4150

January 2016
2-49
WorkCentre WorkCentre 4150/4250/4260WorkCentre 4150/4250/42604150/
07-230, 330, 430
Status Indicator RAPs
• Tray 4. Code 08-400.
11. Check the wiring between the tray feed sensor and CN10 on the Tray PWB. If necessary,
install a new feed sensor, PL 7.25 Item 14.
12. Enter dC330 code. Check that the relevant tray feed motor, PL 7.20 Item 9, runs and
drives the tray transport roll, PL 7.25 Item 22:
• Tray 2. Code 08-920.
• Tray 3. Code 08-930.
• Tray 4. Code 08-940.
13. Check the wiring between the tray feed motor and CN4 on the Tray PWB.
14. While the tray feed motor runs, stack the relevant code to energize the tray pickup clutch.
Check that the tray feed roll, PL 7.25 Item 11 rotates:
• Tray 2. Code 08-820.
• Tray 3. Code 08-830.
• Tray 4. Code 08-840.
15. Check the wiring between the tray pickup clutch and CN4 on the Tray PWB.
16. Check that the following components are clean and rotate freely:
• Tray feed roll, PL 7.25 Item 11.
• Tray nudger roll, PL 8.10 Item 12.
• Tray retard roll, PL 8.10 Item 12.
• Tray transport roll, PL 7.25 Item 22.
• Tray transport roll idlers, part of the tray access door, PL 7.20 Item 18.
17. If necessary, install new components:
• Tray feed roll, PL 7.25 Item 11.
• Tray nudger roll, PL 8.10 Item 12.
• Tray feed motor, PL 7.20 Item 9.
• Tray PWB, PL 7.20 Item 6.
• Tray assembly, PL 7.20 Item 1.
4250/4260/4265 With an HCF
NOTE: The main PWB has 4 test points, GND, +3.3V, +5V and +24V. The location of the test
points is shown on the Main PWB PJ location illustration.
Refer to Wiring Diagram 24, Wiring Diagram 30 and Wiring Diagram 31. Perform the following:
1. Pull out the HCF tray. Remove all jammed paper.
2. Open the HCF access door, PL 7.50 Item 5. Remove all jammed paper.
3. Open the tray 2 access door, PL 7.20 Item 18. Remove all jammed paper.
4. Check the paper path for damage or obstructions.
5. Check that the registration sensor actuator, PL 8.15 Item 5 moves freely and is not dam-
aged. If necessary, install a new registration sensor actuator assembly, PL 8.15 Item 14.
6. Enter dC330 code 08-500. Check the registration sensor (Q08-500), PL 8.15 Item 8.
7. (4250/4260) Check the wiring between the registration sensor and CN12 on the Main
PWB. If necessary, install a new registration sensor, PL 8.15 Item 8.
8. (4265) Check the wiring between the registration sensor and CN27 on the Main PWB. If
necessary, install a new registration sensor, PL 8.15 Item 8.
9. Check that the HCF feed sensor actuator, PL 7.65 Item 14 moves freely and is not dam-
aged.
10. Enter dC330 code 08-300. Check the HCF feed sensor (Q08-300), PL 7.65 Item 14.
11. Check the wiring between the HCF feed sensor and CN10 on the HCF PWB. If neces-
sary, install a new HCF feed sensor, PL 7.65 Item 14.
12. Enter dC330 code 08-930. Check that the HCF feed motor (MOT08-930), PL 7.50 Item
19, runs and drives the HCF transport roll, PL 7.65 Item 8.
13. Check the wiring between the feed motor and CN4 on the HCF PWB. If necessary, install
a new HCF feed motor assembly, PL 7.50 Item 19.
14. While the HCF feed motor runs, stack the code 08-830 to energize the HCF pickup clutch
(CL08-830). Check that the HCF feed roll, PL 8.10 Item 12 rotates.
15. Check the wiring between the HCF pickup clutch and CN4 on the HCF PWB. If neces-
sary, install a new HCF pickup clutch, PL 7.50 Item 16.
16. Enter dC330 code 08-920. Check that the tray 2 feed motor (MOT08-920), PL 7.20 Item
9, runs and drives the tray 2 transport roll, PL 7.25 Item 22.
17. Check the wiring between the tray 2 feed motor and CN4 on the Tray PWB. If necessary,
install a new tray 2 feed motor, PL 7.20 Item 9.
18. Check that the following components are clean and rotate freely, install new components
as necessary:
• HCF feed roll,
PL 8.10 Item 12.
• HCF nudger roll, PL 8.10 Item 12.
• HCF retard roll, PL 8.10 Item 12.
• HCF transport roll, PL 7.65 Item 8.
• HCF transport roll idlers, part of the tray access door, PL 7.50 Item 5.
• Tray 2 transport roll, PL 7.25 Item 22.
• Tray 2 transport roll idlers, part of the tray access door, PL 7.20 Item 18.
19. If necessary, install new components:
• HCF PWB, PL 7.60 Item 7.
•Tray 2 PWB, PL 7.20 Item 6.
20. If necessary, install new a HCF PWB, PL 7.60 Item 7.
21. Perform the OF5 Main PWB Check RAP.