Xerox WorkCentre 4150

January 2016
2-52
WorkCentre WorkCentre 4150/4250/4260WorkCentre 4150/4250/42604150/
07-530
Status Indicator RAPs
07-530 Jam 0 From the Bypass Tray RAP
The feed sensor failed to actuate within the correct time after paper was fed from the bypass
tray.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
NOTE: The main PWB has test points. The location of the test points is shown on the following
PJ location illustrations:
• 4150 Main PWB.
• 4250/4260 Main PWB.
• 4265 Main PWB.
NOTE: The side cover assembly interlock switch must be closed to supply +24V to the motors
and clutches.
Refer to:
• (4150) Wiring Diagram 4, Wiring Diagram 5 and Wiring Diagram 6.
• (4250/4260) Wiring Diagram 24 and Wiring Diagram 25.
• (4265) Wiring Diagram 41 and Wiring Diagram 41.
Refer to Perform the following:
1. Switch off the machine, then switch on the machine.
2. Open the side cover assembly, PL 7.30 Item 1. Remove all jammed paper.
3. Check the paper path for damage or obstructions.
4. Check that the feed sensor actuator, PL 8.15 Item 4 moves freely and is not damaged. If
necessary, install a new feed sensor actuator assembly, PL 8.15 Item 13.
5. Enter dC330 code 08-100. Check the feed sensor (Q08-100), PL 8.15 Item 8.
6. (4150) Check the wiring between the feed sensor and CN13 on the Main PWB. If neces-
sary, install a new feed sensor, PL 8.15 Item 8.
7. (4250/4260) Check the wiring between the feed sensor and CN12 on the Main PWB. If
necessary, install a new feed sensor, PL 8.15 Item 8.
8. (4265) Check the wiring between the feed sensor and CN27 on the Main PWB. If neces-
sary, install a new feed sensor, PL 8.15 Item 8.
9. Enter dC330 code 04-100 to run the main BLDC motor.
10. While the main BLDC motor runs, stack the code 08-800 to energize the bypass feed
clutch (CL08-800). Check that the bypass tray feed roll, PL 8.20 Item 17 rotates.
11. (4150) Check the wiring between the bypass feed clutch, PL 8.20 Item 28 and CN21 on
the Main PWB. Install new components as necessary, PL 8.20.
12. (4250/4260) Check the wiring between the bypass feed clutch,
PL 8.20 Item 28 and CN16
on the Main PWB. Install new components as necessary, PL 8.20.
13. (4265) Check the wiring between the bypass feed clutch, PL 8.20 Item 28 and CN21 on
the Main PWB. Install new components as necessary, PL 8.20.
14. While the main BLDC motor runs, stack the code 08-850 to energize the registration
clutch (CL08-850). Check that the registration roll, PL 4.15 Item 1 rotates.
15. (4150) Check the wiring between the registration clutch, PL 4.15 Item 4 and CN13 on the
Main PWB. Install new components as necessary, PL 4.15.
16. (4250/4260) Check the wiring between the registration clutch, PL 4.15 Item 4 and CN12
on the Main PWB. Install new components as necessary, PL 4.15.
17. (4265) Check the wiring between the registration clutch, PL 4.15 Item 4 and CN27 on the
Main PWB. Install new components as necessary, PL 4.15.
CAUTION
Take note of the spring position before disassembly. The spring clutch must be reassembled
correctly to provide the correct tension.
18. Remove the spring clutch, PL 8.20 Item 30. Clean and lubricate the spring clutch as nec-
essary. If necessary, install a new spring clutch.
19. Clean the retard pad, PL 8.20 Item 4. If necessary, install a new retard assembly, PL 8.20
Item 2.
20. Check that the following components are clean and rotate freely, install new components
as necessary:
• Bypass tray feed roll, PL 8.20 Item 17.
• Registration roll, PL 4.15 Item 1.
• Registration roll idler, PL 4.15 Item 7.
21. If necessary, install a new paper transport assembly, PL 8.20 Item 1.
22. Perform the OF5 Main PWB Check RAP.