Xerox WorkCentre 4150

January 2016
2-4
WorkCentre WorkCentre 4150/4250/4260WorkCentre 4150/4250/42604150/
01-200, 300, 400, 01-500
Status Indicator RAPs
01-200, 300, 400 Tray 2, 3 or 4 Door Open RAP
01-200 The machine has detected that the tray 2 access door is open in standby.
01-300 The machine has detected that the tray 3 access door is open in standby.
01-400 The machine has detected that the tray 4 access door is open in standby.
Procedure
Go to the 07-620, 630, 640 Tray 2, 3, 4 or HCF Door Open RAP.
01-500 Finisher Front Door Open RAP
01-500 The machine has detected that the finisher front door is open. When the front door is
open, there is no +24V supply to the motors.
Procedure
WARNING
Switch off the electricity to the machine. Disconnect the power cord from the customer
supply while performing tasks that do not need electricity. Electricity can cause death or
injury. Moving parts can cause injury.
NOTE: The main PWB has test points. The location of the test points is shown on the following
PJ location illustrations:
• 4150 Main PWB.
• 4250/4260 Main PWB.
• 4265 Main PWB
Refer to Wiring Diagram 14, Perform the following:
1. Check that the finisher door switch actuator on the finisher front door, PL 12.10 Item 1 is
not missing or damaged.
2. Check that the finisher front door closes correctly. Make sure that the front door magnet,
PL 12.10 Item 11 is not missing.
3. Enter dC330 code 12-870. Check the finisher door switch (Q12-870), PL 12.10 Item 4.
4. Check the wiring between the finisher front door switch and J2 on the Finisher PWB. If
necessary, install a new finisher front door switch, PL 12.10 Item 4.
5. Check that the finisher PWB DIP switch settings are correct. Refer to the 12A Finisher
PWB DIP Switch Settings RAP.
6. (4150) Refer to Wiring Diagram 8. Check for +24V at pins 14 and 16 on CN27 on the Main
PWB. If +24V is not available, perform the following:
• Check the wiring between pins 13 and 15 on CON71 on Power Supply Unit 1 and
pins 14 and 16 on CN27 on the Main PWB.
• If necessary, install a new power supply unit 1, PL 1.10 Item 3.
• Perform the OF5 Main PWB Check RAP.
7. (4250/4260) Refer to Wiring Diagram 17. Check for +24V at pins 13 and 14 on CN18 on
the Main PWB. If +24V is not available, perform the following:
• Check the wiring between pins 13 and 14 on CON71 on Power Supply Unit 1 and
pins 13 and 14 on CN18 on the Main PWB.
• If necessary, install a new power supply unit 1, PL 1.15 Item 3.
• Perform the OF5 Main PWB Check RAP.
8. (4265) Refer to Wiring Diagram 33. Check for +24V at pins 3, 4 and 6 on CN33 on the
Main PWB. If +24V is not available, perform the following:
• Check the wiring between pins 1, 3 and 7 on CON71 on Power Supply Unit 1 and
pins 3, 4 and 6 on CN33 on the Main PWB.
• If necessary, install a new power supply unit 1, PL 1.15 Item 3.
• Perform the OF5 Main PWB Check RAP.
9. If necessary, install new components:
• Finisher front door,
PL 12.10 Item 1.