YASKAWA E-7 Series User Manual

3.2 Operating Procedures for Utility Functions
3.2.35 ZONE Table Edit/Save (FnB04)
3-115
3
Utility Functions
3
Move the cursor using the
keys and keys to select the
ZONE table number to be edited.
Refer to the following section for
details on the methods to move the
cursor.
 Method for Moving the Cursor on
page 3-110
4
Press the key to move the cursor
to the setting side of the table.
5
Move the cursor using the
keys and change the ZONE boundary
values using the keys.*
6
On pressing the key, the setting is
entered and the cursor returns to the
ZONE table number side.
7
Repeat steps 3 to 6 to set the ZONE table. On completing the setting of
all the ZONE tables to be used, save the ZONE tables to flash memory
by following the procedure in Saving ZONE Tables on page 3-117.
* If setting is attempted in an operation prohibited state, it will not be possible to
change the setting. In this case, make the setting again by referring to Preparation
on page 3-114.
Continued from previous page.
Step Operation Result
㹀㹀ࠉࠉࠉࠉ㹘㹭㹬㹣㹃㹢㹧㹲
㹘㹌㸮㸮㸰㸻㸩㸮㸮㸮㸮㸮㸮㸮㸮
㹘㹌㸮㸮㸱㸻㸩㸮㸮㸮㸮㸮㸮㸮㸮
㹘㹌㸮㸮㸲㸻㸩㸮㸮㸮㸮㸮㸮㸮㸮
㹘㹌㸮㸮㸳㸻㸩㸮㸮㸮㸮㸮㸮㸮㸮
㹀㹀ࠉࠉࠉࠉ㹘㹭㹬㹣㹃㹢㹧㹲
㹘㹌㸮㸮㸰㸻㸩㸮㸮㸮㸮㸮㸮㸮㸮
㹘㹌㸮㸮㸱㸻㸩㸮㸮㸮㸮㸮㸮㸮㸮
㹘㹌㸮㸮㸲㸻㸩㸮㸮㸮㸮㸮㸮㸮㸮
㹘㹌㸮㸮㸳㸻㸩㸮㸮㸮㸮㸮㸮㸮㸮
㹀㹀ࠉࠉࠉࠉ㹘㹭㹬㹣㹃㹢㹧㹲
㹘㹌㸮㸮㸰㸻㸩㸮㸮㸮㸮㸮㸮㸮㸮
㹘㹌㸮㸮㸱㸻㸩㸮㸮㸮㸮㸮㸮㸮㸮
㹘㹌㸮㸮㸲㸻㸩㸮㸮㸮㸮㸮㸮㸮㸮
㹘㹌㸮㸮㸳㸻㸩㸯㸰㸱㸲㸳㸴㸵㸶
㹀㹀ࠉࠉࠉࠉ㹘㹭㹬㹣㹃㹢㹧㹲
㹘㹌㸮㸮㸰㸻㸩㸮㸮㸮㸮㸮㸮㸮㸮
㹘㹌㸮㸮㸱㸻㸩㸮㸮㸮㸮㸮㸮㸮㸮
㹘㹌㸮㸮㸲㸻㸩㸮㸮㸮㸮㸮㸮㸮㸮
㹘㹌㸮㸮㸳㸻㸩㸯㸰㸱㸲㸳㸴㸵㸶

YASKAWA E-7 Series Specifications

General

Brand	YASKAWA
Model	E-7 Series
Category	Servo Drives
Language	English