1.3 Parameter Table
YASKAWA ELECTRIC TOEP C710687 03B FSDrive-MV1000 Parameter Guide 55
H2-03
(40DH)
Contact Output 3
Function Selection
Refer to H2 Contact Output Settings on page 56 for a description of setting
values.
Default: 0
Min: 0
Max: 1FF
181
H2-04
(40EH)
Contact Output 4
Function Selection
Refer to H2 Contact Output Settings on page 56 for a description of setting
values.
Default: 6
Min: 0
Max: 1FF
181
H2-05
(40FH)
Contact Output 5
Function Selection
Refer to H2 Contact Output Settings on page 56 for a description of setting
values.
Default: 10
Min: 0
Max: 1FF
181
H2-06
(3044H)
Contact Output 6
Function Selection
Refer to H2 Contact Output Settings on page 56 for a description of setting
values.
Default: F
Min: 0
Max: 1FF
181
H2-07
(3045H)
Contact Output 7
Function Selection
Refer to H2 Contact Output Settings on page 56 for a description of setting
values.
Default: F
Min: 0
Max: 1FF
181
H2-08
(3046H)
Contact Output 8
Function Selection
Refer to H2 Contact Output Settings on page 56 for a description of setting
values.
Default: F
Min: 0
Max: 1FF
181
H2-09
(3047H)
Contact Output 9
Function Selection
Refer to H2 Contact Output Settings on page 56 for a description of setting
values.
Default: F
Min: 0
Max: 1FF
181
H2-10
(3048H)
Contact Output 10
Function Selection
Refer to H2 Contact Output Settings on page 56 for a description of setting
values.
Default: F
Min: 0
Max: 1FF
181
H2-11
(3049H)
Contact Output 11
Function Selection
Refer to H2 Contact Output Settings on page 56 for a description of setting
values.
De
fault: F
Min: 0
Max: 1FF
181
H2-12
(304AH)
Contact Output
12
Function Selection
Refer to H2 Contact Output Settings on page 56 for a description of setting
values.
Default: F
Min: 0
Max: 1FF
181
H2-13
(304BH)
Contact Output 13
Function Selection
Refer to H2 Contact Output Settings on page 56 for a description of setting
values.
Default: F
Min: 0
Max: 1FF
181
H2-14
(304CH)
Contact Output 14
Function Selection
Refer to H2 Contact Output Settings on page 56 for a description of setting
values.
Default: F
Min: 0
Max: 1FF
181
H2-15
(304DH)
Contact Output 15
Function Selection
Refer to H2 Contact Output Settings on page 56 for a description of setting
values.
Default: F
Min: 0
Max: 1FF
181
H2-16
(304EH)
Contact Output 16
Function Selection
Refer to H2 Contact Output Settings on page 56 for a description of setting
values.
Default: F
Min: 0
Max: 1FF
181
H2-17
(304FH)
Watt Hour Output
Unit Selection
Outputs a 200 ms pulse signal when the watt-hour counter increases by the
units selected.
0: 0.1 kWh units
1: 1 kWh units
2: 10 kWh units
3: 100 kWh units
4: 1000 kWh units
Default: 0
Min: 0
Max: 4
192
No.
(Addr.)
Name Description Setting Page
MV1000ParameterGuide_E_conditional.book 55 ページ ２０１３年１０月１１日 金曜日 午後８時１８分
To Next Page
Loading...
