3M Attest 390 - Optional 3 M Attest Auto-Reader 390 Web App

9
1
Code/ Issue Problem Solution
Other
Negative ControlVial
BI not properly activated/ media did not contact spore strip.
Ensure BI cap is closed, and glass ampoule is crushed. Tap BI until media flows
to and wets spore strip at bottom of BI.
Other
Negative ControlVial
Control vial was sterilized.
Check process indicator on BI label. Use a non-sterilized vial as a control.
Other
Unexplained PositiveBI
Adhesive residue onvial.
Do not place tape or labels onvial.
Other
Unexplained PositiveBI
Test vial is absorbing fluorescent residue from a chemical indicator or tape.
Place the vial so it does not come in direct contact with chemical indicators or
tape.
Other
3M™Attest™ Auto-reader390will not enter Configurationmode.
Pushbutton Configuration may be disabled on 3M™Attest™
Auto-reader390Web App.
On 3M™Attest™ Auto-reader390Web App Configuration Page, go to
Pushbutton Configuration and select the Enable radio button. Save changes to
begin using new setting.
Other
3M™Attest™ Auto-reader390LCD display flashes and asterisks (***) and/or
E11and/or C4codes appear on display below unoccupied incubation wells.
Move 3M™Attest™ Auto-reader390away from sunlight or sources of
incandescent light.
OPTIONAL 3M™ATTEST™ AUTO-READER 390WEBAPP
Web BrowserRequirements
The Web Interface is designed to be viewed in Internet Explorer 8.0or higher. Earlier
versions of Internet Explorer or other browsers may result in some web pages being
displayed in a less-than-optimum manner. For best results, switching to Internet Explorer
8.0or higher is recommended. For full functionality, the use of an HTML5compliant
browser with JavaScript enabled isrecommended.
Connecting to the 3M™Attest™ Auto-reader390WebApp
To use the 3M™Attest™ Auto-reader390Web App, the 3M™Attest™ 390Auto-reader
must be connected to the facility network using the supplied Ethernet cable. Consult
with your facility IT personnel for assistance with network connectivity. Users may
connect to the 3M™Attest™ Auto-reader390Web App using a URL based upon
either the 3M™Attest™ Auto-reader390serial number or the IP Address. To view
the 3M™Attest™ Auto-reader390Web App from a wireless device such as a
mobile hand-held device or a computer on a sub-net different from that to which the
3M™Attest™ Auto-reader390is connected, use the IP AddressURL.
Note: To access the 3M™Attest™ Auto-reader390Web App within a secure network,
the PC or mobile device must have access to the secure network; options include
connecting via a network Ethernet cable, signing in to the facility’s wireless network, or
connecting via a virtual private network(VPN).
A. Serial numberURL
1. Connect the supplied Ethernet cable from the 3M™Attest™ Auto-reader390to an
Ethernetjack.
2. Depress the button once to display the 3M™Attest™ Auto-reader3906-digit
serial number on the left side of the top row of text on the LCDdisplay.
3. Enter http://attestxxxxxx where xxxxxx represents the unit’s serial number (e.g.,
http://attest001127) from Step 2in PC web browser address bar and pressGo.
4. 3M™Attest™ Auto-reader390Web App Status page will display on PC. For future
ease of use, add this page to your web browser“Favorites.”
B. IP AddressURL
The 3M™Attest™ Auto-reader390Web App may also be accessed using either a
dynamic or static IPaddress.
1. Dynamic IPAddress
A dynamic IP address is assigned when the Ethernet cable is connected from the
3M™Attest™ Auto-reader390to a live Ethernetjack.
Press and release the button twice to display the 3M™Attest™ Auto-reader390’s
dynamic IP address. Enter http://IPaddress (e.g. http://123.45.678.90) in the web browser
address bar of the PC or mobile hand-held device and press Enter. The 3M™Attest™
Auto-reader390Web App Status page willdisplay.
2. Static IPaddress
Some facility IT personnel may require devices connecting to the network to use a Static
IP address. If this is the case at your facility, contact the IT department to request a Static
IPaddress.
Record the static IP address provided by your facility IT department here:___________.
You may wish to label the Ethernet jack with the assigned address. Enter
http://StaticIPaddress (e.g. http://111.22.333.44) in the web browser address bar on your
PC or mobile hand-held device and press Enter. The 3M™Attest™ Auto-reader390Web
App Status page willdisplay.
About the 3M™Attest™ Auto-reader390Web AppPages
The 3M™Attest™ Auto-reader390Web App includes fourpages:
a) Statuspage
Status
History
3M™ Attest™ Auto-reader 390
AT TEST 1291 AT TEST 1292
1 2 3 4 5
+ – – 48 176
6 7 8 9 10
+– –
SN
200004
2012-10-18 14:36
1. User-entered nickname(optional)
2. Well Configuration (1-5and6-10)
3. WellNumber
4. BIResult/Remaining IncubationTime
5. Date andTime
6. 3M™Attest™ Auto-reader390SerialNumber
The Status page provides a real-time representation of the 3M™Attest™
Auto-reader390configuration and LCD panel display. The current date and time and
3M™Attest™ Auto-reader390serial number are also indicated on this page. From this
page, the user may navigateto:
• the History page by clicking on History on the left of thescreen.
• the Results Detail page by clicking on the well number of an occupied well (i.e., a well
that currently has an incubating BI). Clicking on an unoccupied well takes the user to
the Historypage.
Rendered on 5/8/2013 10:56:36 AM
Page 11
34871202858.pdf