ABB ACS580 - Page 359

Additional parameter data 355
22.55 Critical speed 2 high Real -30000.00…30000.00 rpm 100 = 1 rpm
22.56 Critical speed 3 low Real -30000.00…30000.00 rpm 100 = 1 rpm
22.57 Critical speed 3 high Real -30000.00…30000.00 rpm 100 = 1 rpm
22.71 Motor potentiometer function List 0…3 - 1 = 1
22.72 Motor potentiometer initial
value
Real -32768.00…32767.00 - 100 = 1
22.73 Motor potentiometer up source Binary
src
--1 = 1
22.74 Motor potentiometer down
source
Binary
src
--1 = 1
22.75 Motor potentiometer ramp time Real 0.0…3600.0 s 10 = 1 s
22.76 Motor potentiometer min value Real -32768.00…32767.00 - 100 = 1
22.77 Motor potentiometer max
value
Real -32768.00…32767.00 - 100 = 1
22.80 Motor potentiometer ref act Real -32768.00…32767.00 - 100 = 1
22.86 Speed reference act 6 Real -30000.00…30000.00 rpm 100 = 1 rpm
22.87 Speed reference act 7 Real -30000.00…30000.00 rpm 100 = 1 rpm
23 Speed reference ramp
23.01 Speed ref ramp input Real -30000.00…30000.00 rpm 100 = 1 rpm
23.02 Speed ref ramp output Real -30000.00…30000.00 rpm 100 = 1 rpm
23.11 Ramp set selection Binary
src
--1 = 1
23.12 Acceleration time 1 Real 0.000…1800.000 s 1000 = 1 s
23.13 Deceleration time 1 Real 0.000…1800.000 s 1000 = 1 s
23.14 Acceleration time 2 Real 0.000…1800.000 s 1000 = 1 s
23.15 Deceleration time 2 Real 0.000…1800.000 s 1000 = 1 s
23.20 Acc time jogging Real 0.000…1800.000 s 1000 = 1 s
23.21 Dec time jogging Real 0.000…1800.000 s 1000 = 1 s
23.23 Emergency stop time Real 0.000…1800.000 s 1000 = 1 s
23.28 Variable slope List 0…1 - 1 = 1
23.29 Variable slope rate Real 2…30000 ms 1 = 1 ms
23.32 Shape time 1 Real 0.000…1800.000 s 1000 = 1 s
23.33 Shape time 2 Real 0.000…1800.000 s 1000 = 1 s
24 Speed reference conditioning
24.01 Used speed reference Real -30000.00…30000.00 rpm 100 = 1 rpm
24.02 Used speed feedback Real -30000.00…30000.00 rpm 100 = 1 rpm
24.03 Speed error filtered Real -30000.0…30000.0 rpm 100 = 1 rpm
24.04 Speed error inverted Real -30000.0…30000.0 rpm 100 = 1 rpm
24.11 Speed correction Real -10000.00…10000.00 rpm 100 = 1 rpm
24.12 Speed error filter time Real 0…10000 ms 1 = 1 ms
25 Speed control
25.01 Torque reference speed
control
Real -1600.0…1600.0 % 10 = 1%
No. Name Type Range Unit FbEq32
ACS580 FW.book Page 355 Wednesday, September 21, 2016 9:48 PM