ABB FSPS-21 - Module Terminals and Connection Details

￭ Terminals
DescriptionConnect-
or
Electrical installation
 Layout of the module
 Connection procedure
1. Connect the network cable to connector [X1] on the module.
2. If you want to create a daisy chain network with the FSPS-21 modules, connect connector [X2] of the
first module to connector [X1] on the next module, and so on.
3. Connect the STO cable to the FSPS-21 module (black connector).
4. ACS880: Connect the yellow connector to drive’s STO connector. ACS380/580: Remove the yellow
connector from the cable and connect the wires to drive’s STO connectors (see figure below).
Start-up
See the user’s manual.
Further information
See the latest version of FSPS-21 safety functions fieldbus
module user's manual (3AXD50000158638 [English]) in ABB
library (www.abb.com/drives/documents
).
For more information on ABB safety information and solutions,
see ABB Safety information and solutions web page
(new.abb.com/safety
).
No. Description
1Lock
2 Mounting and grounding screw
3 RJ-45 connector [X1] to Ethernet
4 RJ-45 connector [X2] for chaining another module
5 STO connector (under connectors [X1] and [X2])
6 Diagnostic LEDs
7MAC ID
A
ACS580 drive
Control unit
FSPS-21
ACS380 drive
Control unit
S+
SGND
S1
S2
FSPS-21
Red
White
Black
Yellow
STO
34
35
36
37
38
STO
Red
White
Black
Yellow
STO
STO
3AXD50000158591 Rev A (EN) 2018-02-08
FSPS-21 manual
ABB Safety information and solutions
Mounting and grounding screwA
X1 connector to EthernetX1
X2 connector for chaining another moduleX2
STO connectorSTO
1. Connect the network cable to connector [X1] on the module.
2. If you want to create a daisy chain network with the modules, connect connector [X2]
of the first module to connector [X1] on the next module, and so on.
3. Connect the STO cable to the module (black connector).
4. ACS880: Connect the yellow connector to drive’s STO connector. ACS380/580: Remove
the yellow connector from the cable and connect the wires to drive’s STO connectors
(see figure below).
Electrical installation
 Layout of the module
 Connection procedure
1. Connect the network cable to connector [X1] on the module.
2. If you want to create a daisy chain network with the FSPS-21 modules, connect connector [X2] of the
first module to connector [X1] on the next module, and so on.
3. Connect the STO cable to the FSPS-21 module (black connector).
4. ACS880: Connect the yellow connector to drive’s STO connector. ACS380/580: Remove the yellow
connector from the cable and connect the wires to drive’s STO connectors (see figure below).
Start-up
See the user’s manual.
Further information
See the latest version of FSPS-21 safety functions fieldbus
module user's manual (3AXD50000158638 [English]) in ABB
library (www.abb.com/drives/documents
).
For more information on ABB safety information and solutions,
see ABB Safety information and solutions web page
(new.abb.com/safety
).
No. Description
1Lock
2 Mounting and grounding screw
3 RJ-45 connector [X1] to Ethernet
4 RJ-45 connector [X2] for chaining another module
5 STO connector (under connectors [X1] and [X2])
6 Diagnostic LEDs
7 MAC ID
6
32
4
1
5
7
ACS580 drive
Control unit
FSPS-21
ACS380 drive
Control unit
SGND
S+
FSPS-21
Red
White
Black
Yellow
STO
34 OUT1
35
36 DGND
37 IN1
38 IN2
Red
White
Black
Yellow
STO
STO
S1
S2
3AXD50000158591 Rev A (EN) 2018-02-08
FSPS-21 manual
ABB Safety information and solutions
40 Electrical installation