Index
Product manual 2CKA001473B5023
232
L
Legend ...................................................... 222
M
Micro SD card (SDHC) ......................... 210, 211, 218
N
Navigation structure
Creation .................................................................... 22, 26
network
settings ........................................................................... 14
Notes ....................................................... 228
O
Opening the door ......................................... 206
Operating actions of the application .................. 205
Operating mode after reset ............................. 140
Operating pages
Configuration .................................................................. 29
Creating .......................................................................... 26
Editing ............................................................................. 27
Operation ............................................. 21, 189
P
Panel
Basic settings ..................................................... 22, 23, 36
Basic structure .......................................................... 20, 26
Practice-oriented examples ............................. 224
Practice-oriented examples for application .......... 224
Prerequisites ............................................... 11
Presence simulation ...................................... 209
R
Reset all ..................................................... 45
Reset layout ................................................ 45
Return to the previous page ............................ 204
S
Setpoint adjustment — Maximum manual increase
during cooling mode (0 - 9°C) ....................... 163
Setpoint adjustment — Maximum manual increase
during heating mode (0 - 9°C) ...................... 149
Setpoint adjustment — Maximum manual reduction
during cooling mode (0 - 9°C) ....................... 164
Setpoint adjustment — Maximum manual reduction
during heating mode (0 - 9°C) ...................... 150
Setpoint adjustment — Permanent storage of on-site
operation ......................................... 151, 165
Setpoint adjustment — Resetting of the manual
adjustment for receipt of a basic setpoint .. 150, 164
Setpoint adjustment — Resetting the manual
adjustment for change of operating mode .. 150, 164
Setpoint adjustment — Resetting the manual
adjustment via object .......................... 151, 165
Setpoint settings — Cyclic sending of the current set-
point temperature (min) ....................... 149, 163
Setpoint settings — Hysteresis for switchover
heating/cooling ........................................ 176
Setpoint settings — Increase for ECO cooling (°C) .. 162
Setpoint settings — Increase for standby cooling (°C)
........................................................... 162
Setpoint settings — Reduction for ECO heating (°C) 148
Setpoint settings — Reduction for standby heating (°C)
.......................................................... 148
Setpoint settings — Send current setpoint ..... 149, 163
Setpoint settings — Setpoint for heating comfort =
setpoint for cooling comfort ........................ 175
Setpoint settings — Setpoint temperature for cooling
comfort (°C) ........................................... 162
Setpoint settings — Set-point temperature for frost
protection (°C) ........................................ 149
Setpoint settings — Set-point temperature for heat
protection (°C) ........................................ 163
Setpoint settings — Setpoint temperature for heating
and cooling comfort (°C) ............................ 176
Setpoint settings — Setpoint temperature for heating
comfort (°C) ........................................... 148
Settings of basic load — Minimum control value for
basic load > 0 .................................... 147, 161
Special functions ......................................... 201
Summer compensation .................................. 169
Summer compensation — (Lower) Starting temperature
for summer compensation (°C) ..................... 171
Summer compensation — Offset of the set-point
temperature for the entry into summer
compensation (x 0.1°C) .............................. 171
Summer compensation — Offset of the set-point
temperature for the exit from summer
compensation (x 0.1°C) .............................. 172
Summer compensation — Summer compensation ... 170
Switching light ............................................ 207
System settings ........................................... 218
T
Temperature reading — Adjustment value for internal
temperature measurement (x 0.1°C) ........ 153, 167
Temperature reading — Control value for fault (0 -
255) ............................................... 154, 168
Temperature reading — Cyclic sending of actual
temperature (min) .............................. 152, 166
Temperature reading — Difference of value for sending
the actual temperature (x 0.1°C) ............ 153, 167
Temperature reading — Inputs of temperature reading
.................................................... 151, 165
Temperature reading — Inputs of weighted
temperature reading ........................... 151, 166
Temperature reading — Monitoring time for
temperature reading (0 = no monitoring) (min) 153,
168
Temperature reading — Operating mode for fault .. 176
Temperature reading — Weighting of external
measurement (0 to 100%) ..................... 152, 166
Temperature reading — Weighting of external
measurement 2 (0 to 100%) ................... 152, 166
Temperature reading — Weighting of internal
measurement (0 to 100%) ..................... 152, 166
Time programs ................................ 201, 202, 214
Tools (functions) ........................................... 44
transfer of pid file (configuration file) ............... 221
To Next Page
Loading...
