Table of contents
Product manual 2CKA001473B5023
8
2.21.52
Cooling control — P-component (x 0.1°C) .................................................................................157
2.21.53
Cooling control — I-component (min.) .......................................................................................157
2.21.54
Cooling control - Extended settings ...........................................................................................157
2.21.55
Basic stage cooling ...................................................................................................................158
2.21.56
Basic stage cooling — Status object cooling .............................................................................158
2.21.57
Basic stage cooling — Mode of the control value ......................................................................158
2.21.58
Basic stage cooling — Hysteresis (x 0.1°C) ..............................................................................159
2.21.59
Basic stage cooling — Cyclic sending of the control value (min) ...............................................159
2.21.60
Basic stage cooling - PWM cycle cooling (min) .........................................................................160
2.21.61
Basic stage cooling — Maximum control value (0 - 255) ...........................................................160
2.21.62
Basic stage cooling — Minimum control value for basic load (0 to 255) ....................................160
2.21.63
Settings of basic load — Minimum control value for basic load > 0 ...........................................161
2.21.64
Basic load settings — Basic load active when controller is off ...................................................161
2.21.65
Setpoint settings — Setpoint temperature for cooling comfort (°C) ...........................................162
2.21.66
Setpoint settings — Increase for standby cooling (°C) ..............................................................162
2.21.67
Setpoint settings — Increase for ECO cooling (°C) ...................................................................162
2.21.68
Setpoint settings — Set-point temperature for heat protection (°C) ...........................................163
2.21.69
Setpoint settings — Send current setpoint ................................................................................163
2.21.70
Setpoint settings — Cyclic sending of the current set-point temperature (min) ..........................163
2.21.71
Setpoint adjustment — Maximum manual increase during cooling mode (0 - 9°C) ...................163
2.21.72
Setpoint adjustment — Maximum manual reduction during cooling mode (0 - 9°C) ..................164
2.21.73
Setpoint adjustment — Resetting of the manual adjustment for receipt of a basic setpoint .......164
2.21.74
Setpoint adjustment — Resetting the manual adjustment for change of operating mode ..........164
2.21.75
Setpoint adjustment — Resetting the manual adjustment via object .........................................165
2.21.76
Setpoint adjustment — Permanent storage of on-site operation ...............................................165
2.21.77
Setpoint adjustment — Permanent storage of on-site operation ...............................................165
2.21.78
Temperature reading — Inputs of temperature reading .............................................................165
2.21.79
Temperature reading — Inputs of weighted temperature reading .............................................166
2.21.80
Temperature reading — Weighting of internal measurement (0 to 100%) .................................166
2.21.81
Temperature reading — Weighting of external measurement (0 to 100%) ................................166
2.21.82
Temperature reading — Weighting of external measurement 2 (0 to 100%) .............................166
2.21.83
Temperature reading — Cyclic sending of the actual temperature (min) ...................................166
2.21.84
Temperature reading — Difference of value for sending the actual temperature (x 0.1°C) ........167
2.21.85
Temperature reading — Adjustment value for internal temperature measurement (x 0.1°C) ....167
2.21.86
Temperature reading — Monitoring time for temperature reading (0 = no monitoring) (min) .....168
2.21.87
Temperature reading — Control value for fault (0 - 255) ...........................................................168
2.21.88
Alarm functions - Condensate water alarm ................................................................................168
2.21.89
Alarm functions — Dew point alarm ..........................................................................................169
2.21.90
Alarm functions — Frost alarm temperature for HVAC and RHCC status (°C) ..........................169
2.21.91
Alarm functions — Heat alarm temperature for RHCC status (°C) ............................................169
2.21.92
Summer compensation .............................................................................................................169
2.21.93
Summer compensation — Summer compensation ...................................................................170
2.21.94
Summer compensation -— (Lower) Starting temperature for summer compensation (°C) ........171
2.21.95
Summer compensation — Offset of the set-point temperature for the entry into summer
compensation (x 0.1°C) .............................................................................................................171
2.21.96
Summer compensation — (Upper) exit temperature for summer compensation (°C) ................171
2.21.97
Summer compensation — Offset of the set-point temperature for the exit from summer
compensation (x 0.1°C) .............................................................................................................172
2.21.98
Control of additional cooling stage — Cooling type ...................................................................173
2.21.99
Control of additional cooling stage — P-component (x 0.1°C) ...................................................173
2.21.100
Control of additional cooling stage — P-component (min) .........................................................174
2.21.101
Combined heating and cooling modes ......................................................................................174
To Next Page
Loading...
