418 Agilent InfiniiVision 3000 X-Series Oscilloscopes User's Guide
Index
CAN decode, source channels, 336
CAN frame counter, 341
CAN serial decode, 339
CAN totalizer, 341
CAN trigger, 337
capture signal bursts, 197
cardiac waveform generator output, 254
Center, FFT, 81
channel labels, 135
channel, analog, 61
channel, bandwidth limit, 65
channel, coupling, 63
channel, invert, 66
channel, on/off keys, 39
channel, position, 63
channel, probe units, 67
channel, skew, 68
channel, vernier, 65
channel, vertical sensitivity, 63
characteristics, 315
chart logic bus state math function, 97
chart logic bus timing math function, 96
choosing values, 35
cleaning, 297
clear display, 194
clear display, Quick Clear Display, 299
clear persistence, 132
clock, 292
CMOS threshold, 111
common logarithm math function, 90
COMP license, 323
compensate passive probes, 32, 39
Config softkey, 285
, 286
connect probes, digital, 103
connection, to a PC, 286
connectors, rear panel, 42
control, remote, 283
controls, front panel, 33
copyright, 2
Counter measurement, 227
counter, ARINC 429 words/errors, 404
counter, CAN frame, 341
counter, FlexRay frame, 357
counter, UART/RS232 frame, 414
coupling, channel, 63
coupling, trigger, 180
crosstalk problems, 81
CSV file format, 264
CSV files, minimum and maximum
values, 333
current probes, 321
cursor measurements, 203
cursor units, 206
Cursors key, 38
Cursors knob, 38
cursors, binary, 205
cursors, hex, 205
cursors, manual, 204
cursors, track waveform, 205
D
D*, 37, 111
d/dt math function, 77
damage, shipping, 23
data sheet, 315
DC channel coupling, 64
DC offset correction for integrate
waveform, 79
DC RMS - Full Screen measurement, 223
DC RMS - N Cycles measurement, 223
DC signals, checking, 179
DC waveform generator output, 253
dead time (re-arm), 200
decibels, FFT vertical units, 82
decimating samples, 191
decimation, for measurement record, 333
decimation, for screen, 333
default configuration, 29
default label library, 139
default setup, 29, 276
Default Setup key, 36
defaults, waveform generator, 261
delay knob, 49
Delay measurement, 216, 229
delay time indicator, 57
delayed sweep, 54
delete character, 273
delete file, 287
Demo 1 terminal, 39
Demo 2 terminal, 39
DHCP, 285, 286
differential probes, 320
differentiate math function
, 77
Digit softkey, 153
digital bus mode, 112
digital channel controls, 37
digital channel inputs, 40
digital channel menu, 110
digital channels, 110
digital channels, AutoScale, 107
digital channels, enabling, 325
digital channels, logic threshold, 110
digital channels, probing, 115
digital channels, size, 109
digital display, interpreting, 108
Digital key, 37
digital probes, 103, 115
digital probes, impedance, 115
Display key, 38
display multiple acquisitions, 186
display, area, 44
display, interpreting, 43
display, persistence, 131
display, signal detail, 129
display, softkey labels, 45
display, status line, 44
displayed channels AutoScale, 291
distortion problems, 81
Divide math function, 75
DNS IP, 285
Duty cycle measurement, 228
duty cycle measurement trend, 96
Dynamic DNS, 285
E
ECL threshold, 111
edge speeds, 190
edge then edge triggering, 146
edge triggering, 144
EDK license, 323
EEPROM data read, I2C trigger, 363
either edge trigger, 145
EMBD license, 323
energy of a pulse, 78
English user interface and Quick Help, 46
Entry knob, 35
Entry knob, push to select, 35
erase, secure, 277
event table, 124
expand about, 63, 289
expand about center, 290
expand about ground, 289
exponential fall waveform generator
output, 253
To Next Page
Loading...
Need help?
General
