Need help?Do you have a question about the Allen-Bradley DeviceNet 1761-NET-DNI and is the answer not in the manual?
General| Device Type | DeviceNet Interface |
|---|---|
| Protocol | DeviceNet |
| Manufacturer | Allen-Bradley |
| Catalog Number | 1761-NET-DNI |
| Communication Speed | 125, 250, or 500 Kbps |
| Power Supply | 24V DC |
| Relative Humidity | 5 to 95% non-condensing |
| DeviceNet Node Address | 0 to 63 |
| Dimensions (H x W x D) | 90 x 40 x 87 mm (3.54 x 1.57 x 3.43 in) |
Identifies information about practices or circumstances that can lead to personal injury or death, property damage or economic loss.
Identifies information that is critical for successful application and understanding of the product.
Product compliance with EU directives for EMC and Low Voltage.
Equipment suitability and warnings for hazardous locations.
Procedures for DIN rail and panel mounting of the unit.
Guidelines for DeviceNet network and port identification.
Details on RS-232 compatible cables for various devices.
Information on required software files for DNI configuration and interface.
Instructions for configuring network software like RSNetWorx and DeviceNet Manager.
Steps for initial setup and configuration of the DNI on the network.
Methods for programming controllers via DeviceNet.
Procedures for changing DNI configuration parameters using utilities.
Details new features and compatibility issues between DNI Series A and B.
Identifies the intended audience and required knowledge for using the manual.
Explains the manual's role as a guide for DNI installation and configuration.
Overview of the DeviceNet Interface (DNI) as a protocol conversion device.
Describes the DNI's capabilities in peer-to-peer and DeviceNet slave modes.
Lists controllers and products compatible with the DNI for interconnection.
Steps to establish peer-to-peer communication between controllers via DNI.
Procedure to configure a DNI as a slave device to a DeviceNet master.
Details the primary features and usage modes of the DeviceNet Interface.
Explains how the DNI handles I/O data with a DeviceNet master.
Describes the capabilities and types of explicit messaging supported by the DNI.
Explains PCCC messaging over DeviceNet using DF1 protocol.
Covers methods for programming and accessing controllers via DeviceNet.
Details how to gain remote access to DeviceNet networks using modems.
Highlights changes affecting the EDS file for DNI Series B.
Lists and defines available parameters for configuring the DNI.
Defines the size of the data array read from the attached controller.
Determines data allocation between Master/Slave I/O and explicit messaging.
Identifies the data file to be read within the controller.
Specifies the starting word for reading data from the controller.
Defines the size of the data array written to the attached controller.
Determines data allocation between Master/Slave I/O and explicit messaging for output.
Identifies the type of data to be written to the controller.
Specifies the starting word for writing data to the controller.
Selects the device connected to the DNI's RS-232 port for communication.
Enables or disables the DNI's scan/exchange of I/O data with DF1 devices.
Detects communication path integrity and controller scanning status.
Defines the time delay between communication sequences.
Sets the duration an explicit connection is held open after message completion.
Automatically routes DF1 communications to a specified address.
Configures RS-232 baud rate synchronization for DF1 devices.
Enables automatic synchronization of the DNI to the DeviceNet network baud rate.
Sets the DNI operational mode (Standby or Operational).
Provides notes on input messaging, considerations, and controller file usage.
Information on obtaining and installing DNI EDS and bitmap files for configuration.
Guides on integrating DNI files with RSNetWorx and DeviceNet Manager.
Steps to set node address and baud rate for DNI network integration.
Procedures for uploading, downloading, and monitoring programs via DeviceNet.
How to change DNI parameters using configuration utilities.
Explains the meaning of DNI module status and network status LEDs.
Identifies causes of DNI faults and available recovery options.
Details the Identity Object attributes for DNI Series A.
Describes input and output assembly data for slave I/O configuration.
Details the Identity Object attributes for DNI Series B.
Example of using a MicroLogix controller as an I/O block on DeviceNet.
Lists DNI parameters used in the ladder logic examples.
Provides ladder logic examples for monitoring DNI communication integrity.
Details ladder logic for monitoring the heartbeat between DNI and MicroLogix.
Example of implementing Change of State (COS) I/O messaging with the DNI.
Explains using DF1 protocol for explicit messaging with DeviceNet.
Describes how to configure routing profiles for explicit messaging.
Demonstrates reading data from a DeviceNet device using explicit messaging.
Demonstrates writing data to a DeviceNet device using explicit messaging.
Details electrical and environmental specifications of the DNI.
Lists features and comments related to DeviceNet functionality.
Provides physical dimensions of the DNI unit.
Offers a template for drilling holes for mounting the DNI.
Explains the relationship between the DF1 Device, DNI, and DeviceNet network.
Defines key terms and abbreviations specific to the DNI and DeviceNet.
To Next Page
