Alliance Laundry Systems PA20 X CONTROL - Failure 600-628: Software Errors

110 pages

To Next Page

To Previous Page

Failure 600-628: Software Errors

Software errors must never occur. If a software error message oc-

curs inform the manufacturer.

Troubleshooting

DO NOT COPY or TRANSMIT

108 Part No. D1676ENR11

Main Page

Table of Contents3
Safety Information8
Important Safety Instructions8
Introduction9
Model Identification9
Machine Type in Configuration Menu9
Control Identification10
Symbol Used10
Main Menu11
Basic Description of Controls13
General13
Specific13
Entering and Changing Values Utilizing the Control Keypad14
How to Get into the Setup Mode14
15 Wash Programs - 99 Steps15
Available Wash Sequences16
The Creation of a Wash Program16
Programming the Wash Sequence16
Programming the Drain Sequence16
The Tumble Sequence16
Programming the Functions16
Programming the Water Temperature16
Programming the Water Inlets Valves16
Top Soap Dispenser Machines16
Programming the Water Level17
Cabinet Freestanding 6.5-28 Kg / 14-70 Lb / 65-280 L18
Cabinet Hardmount 7.5-52 Kg / 20-120 Lb / 80-520 L19
Programmable Water Level23
Speed of Machines with Frequency Inverter23
Programming the Wash Speed25
Programming Extraction Speed25
Programming Supplies25
Programming the Motor on and off Times for Reversing25
Programming the Sequence Time25
Signal26
Initializing the Machine27
Initialization Menu27
Configuration Menu31
Passwords32
Advanced Menu36
Hygienic Cycle Menu36
Program Mode Lock Menu37
Program Lock Menu38
Weighing Menu39
Data EXPORT / IMPORT40
Payment Menu40
Selection of Payment Mode42
Selection of Additional Functions42
Audit Data Menu43
Programming47
General47
Step 1: Program Menu47
Step 2: Program Functions47
Step 3: Program Step Function48
Step 4: Programming the Wash Part50
Selecting the Wash Part50
The Prewash Sequence51
The Wash Sequence52
The Cooldown Sequence53
The Rinse Sequence54
The Extra Rinse Sequence55
The Final Rinse Sequence56
The Soak Sequence57
The Spray Sequence58
The no Wash Sequence59
Step 5: Programming the Drain Step59
Selecting the Drain / Extraction Step59
The Drain Sequence60
The Extract Sequence60
The no Drain Sequence61
The Static Drain Sequence61
The Reversing Drain Sequence61
Operation Menu63
Starting up63
Switching on the Power63
Load the Washing Machine63
Put Soap into the Soap Dispenser63
Starting a Wash Program63
The Active Program63
Advancing a Wash Program64
Wash Time64
Program End64
Water Fill Process64
Heating Process64
Cooldown Function65
Spray Function65
Unbalance65
Adding Detergents65
Wait State65
How to Handle Failure Messages65
How to Handle Power Interruptions66
Special Functions66
External Liquid Soap Boxes66
Pre-Programmed Programs67
Water Inlets (Valves) Information67
Wash Program Legend Water Levels67
Wash Actions67
RPM (Revolutions Per Minute)67
Wash Programs68
Wash Program 1: Normal Hot 140°F [60°C]68
Wash Program 2: Normal Warm 95°F [35°C]69
Wash Program 3: Normal Cold 59°F [15°C]70
Wash Program 4: Extra Wash Hot 140°F [60°C]70
Wash Program 5: Extra Wash Warm 95°F [35°C]71
Wash Program 6: Pernament Press 95°F [35°C]72
Wash Program 7: Delicates 59°F [15°C]73
Wash Program 8: Bulky 95°F [35°C]74
Wash Program 9: Denim 95°F [35°C]75
Wash Program 10: Whites 140°F [60°C]76
Wash Program 11: Colors 59°F [15°C]77
Wash Program 12: Casual 95°F [35°C]78
Wash Program 13: Sport Fabrics 95°F [35°C]78
Wash Program 14: Wool 59°F [15°C]79
Wash Program 15: Rinse & HI Spin80
Troubleshooting81
Display Messages81
Fault Messages81
How to Handle Fault Messages81
Failure Message Overview82
Service Menu84
Faults Menu (Service Faults)85
Toolbox Menu86
Diagnostic Program87
Test Sequence89
Basic Diagnostic Wash Program90
Troubleshooting91
External Communication Problems92
Error Message Descriptions92
Failure 2: Drain Failure92
Failure 3: Safety Switch Activated92
Failure 4: the Linen Is Not Correctly Distributed in the Stage When the Machine Starts up the Spinning Sequence93
Failure 5: Safety Switch High Spin93
Failure 6: Door Switch Failure93
Failure 7: Door Lock Switch Failure94
Failure 8: Door Close Check at Start Failure94
Failure 9: Door Lock Switch Failure at Cycle End94
Failure 10: Target Temperature Not Reached95
Failure 11: Fill Failure95
Failure 12: Overfill Failure95
Failure 13: Heating Failure96
Failure 14: Heating Time Failure96
Failure 15: too Hot96
Failure 16: Coin Blocking 197
Failure 17: Coin Blocking 297
Failure 18: Door Lock Pre-Test before Start97
Failure 19: Door Lock Test after Start97
Failure 21: Overflow Failure97
Failure 24: Defective Level Sensor98
Failure 25: Defective Temperature Sensor98
Failure 26: Undefined Mitsubishi Frequency Inverter Error Code98
Failure 27: Communication Fault Inverter98
Failure 28: THT (Mitsubishi) Time out99
Failure 29: OV3 (Mitsubishi) Time out99
Failure 31: Initialization Fault Inverter99
Failure 32: Verification Fault Inverter99
Failure 35: Wrong Software Version100
Failure 36: the Linen Is Not Correctly Distributed in the Stage before the Start up of the Spinning Sequence100
Failure 37: Drain Failure at the Spray Sequence100
Failure 39: Empty Soap Supply Box100
Failure 41: Service Due Warning100
Failure 42: no Network Connection101
Failure 43: Wrong Voltage Range Selection101
Failure 44: Incorect Selection of Machine Type101
Failure 45: Drum Rotation Sensor Is Not Working101
Failure 60: Inner Door Lock101
Failure 77: Time for Heating Blocking Is out102
Failure 80: Time for Dispensing Liquid Detergents Is out102
Failure 85: RTC Low Battery102
Failure 95: Watch Dog102
Failure 106: Calibration Error102
Failure 107: Not Calibrated103
Failure 300-353: Mitsubishi Inverter Alarm Message103
Failure 500-526: Memory Errors107
Failure 560: USB Not Found107
Failure 561: File Not Found107
Failure 562: Export Failed107
Failure 563: Import Failed107
Failure 570-571: Card Reader Error107
Failure 600-628: Software Errors108
Service Information109
Maintenance109

Alliance Laundry Systems PA20 X CONTROL - Failure 600-628: Software Errors

Table of Contents

Other manuals for Alliance Laundry Systems PA20 X CONTROL

Related product manuals