Binder CB 170 - Dimensions

To Next Page

To Previous Page

CB (E7) 06/2018 Page 165/174

25.9 Dimensions

CB 170

(Dimensions in mm)

Main Page

Default Chapter2
- Table of Contents2
Safety7
- Legal Considerations7
- Structure of the Safety Instructions7
- Localization / Position of Safety Labels on the Chamber10
- Type Plate11
- General Safety Instructions on Installing and Operating the CO Incubator12
- Precautions When Working with Gases13
- Precautions When Handling Gas Cylinders15
- Intended Use16
- Measures to Prevent Accidents17
- Resistance of the Humidity Sensor against Harmful Substances18
Chamber Description19
- Chamber Overview20
- Inner Chamber21
- Control Panel on the Rear of the Chamber22
3 Completeness of Delivery, Transportation, Storage, and23
- Instrument Panel23
  - Installation23
- Unpacking, and Checking Equipment and Completeness of Delivery23
- Guidelines for Safe Lifting and Transportation24
- Storage24
- Location of Installation and Ambient Conditions25
Installation and Connections28
- Shelves28
- Permadry™ Water Pan28
- Connecting the O29
  - Control)29
- Gas Connections30
- Water Supply for the Chamber with Active Humidification36
- Electrical Connection38
- Handling and Aligning the Divided Inner Door, Gas Proof (Optional Equipment)39
Functional Overview of the Mb2 Chamber Controller40
- Operating Functions in Normal Display41
- Display Views: Normal Display, Program Display, Chart-Recorder Display42
- Controller Icons Overview43
- Operating Modes45
- Controller Menu Structure46
- Principle of Controller Entries49
- Performance During and after Power Failures49
- Performance When Opening the Door50
Start up50
- Turning on the Chamber50
- Controller Settings Upon Start up51
- Entering the Altitude of the Installation Site52
- Factory Settings52
- Equilibration Time53
- Operating the Duodoor™ Door Lock53
- Required Gas Supply for the Chamber with O54
- Activating / Deactivating CO and Humidity Control55
- Humidity Control of the Permadry™ System56
Set-Point Entry in "Fixed Value" Operating Mode57
- Set-Point Entry through the "Setpoints" Menu58
- Direct Setpoint Entry Via Normal Display59
- Special Controller Functions Via Operation Lines60
- Safety Instructions for Setting High Gas Concentrations61
Timer Program: Stopwatch Function62
- Starting a Timer Program62
  - Performance During Program Delay Time62
- Stopping a Running Timer Program63
  - Pausing a Running Timer Program63
  - Cancelling a Running Timer Program63
- Performance after the End of the Program63
Time Programs64
- Starting an Existing Time Program64
  - Performance During Program Delay Time65
- Stopping a Running Time Program65
  - Pausing a Running Time Program65
  - Cancelling a Running Time Program65
- Performance after the End of the Program65
- Creating a New Time Program66
- Program Editor: Program Management66
  - Deleting a Time Program67
- Section Editor: Section Management68
- Value Entry for a Program Section71
Week Programs78
- Starting an Existing Week Program78
- Cancelling a Running Week Program78
- Creating a New Week Program79
- Program Editor: Program Management80
  - Deleting a Week Program81
- Section Editor: Section Management82
- Value Entry for a Program Section84
Notification and Alarm Functions87
- Notification and Alarm Messages Overview87
  - Notifications87
  - Alarm Messages88
- State of Alarm90
- Resetting an Alarm, List of Active Alarms90
- Activating / Deactivating the Audible Alarm (Alarm Buzzer)91
- Tolerance Range Settings and Alarm Delay Times91
- Zero-Voltage Relay Alarm Output93
Temperature Safety Devices94
- Over Temperature Protective Device (Class 1)94
- Overtemperature Safety Controller Class 3.194
User Management97
- Authorization Levels and Password Protection97
- Log in100
- Log out101
- User Change101
- Password Assignment and Password Change102
- Activation Code106
General Controller Settings107
- Selecting the Controller's Menu Language107
- Setting Date and Time107
- Selecting the Temperature Unit109
- Display Configuration109
  - Adapting the Display Parameters109
  - Touchscreen Calibration110
- Network and Communication111
- USB Menu: Data Transfer Via USB Interface115
General Information116
- Service Contact Page116
- Current Operating Parameters116
- Event List117
- Technical Chamber Information117
Chart Recorder Display118
- Views118
- Setting the Parameters122
Humidification System (Chamber with Active Humidification)123
- Function of the Humidifying System123
Options124
- Communication Software APT-COM™ 3 Datacontrolsystem (Option)124
- Silicone Access Ports 30 MM / 1.18 In, Closable from both Sides with Silicon Plugs (Option)124
- Interior Socket 230V (Option, Available Via BINDER INDIVIDUAL Customized Solutions)125
- Analog Outputs for Temperature and CO127
- Data Logger Kits (Option)127
- Access Port for Extra-Low Voltage (Option)128
- BINDER Gas Supply Service - External Bottle Changer for CO129
- Stands129
Reference Measurements130
- CO Reference Measuring130
  - Measuring CO130
- Concentration Indirectly Via the Ph of the Cell Medium130
  - Measuring CO131
- Directly Via Chemical Indicator Tubes131
- Directly with an Electronic Infrared Measuring Device131
- Temperature Reference Measurement131
Avoiding Microbial Contamination132
- Cells and Media132
- Laboratory Conditions / Equipment Around the Incubator132
- Working and Behavior in the Lab132
- Chamber Design and Equipment of the CO133
- Incubator133
- Handling the CO Incubator134
Cleaning, Decontamination / Disinfection, and Sterilization135
- Cleaning135
- Decontamination / Chemical Disinfection of the Chamber137
- Hot-Air Sterilization at 180 °C / 356 °F138
Maintenance and Service144
- Maintenance Intervals, Service144
- Checking the Humidity System Fan145
- Gas Inlet Fine Filter145
- Replacing the CO145
  - Sensor145
- Sending the Chamber Back to BINDER Gmbh146
Disposal147
- Disposal of the Transport Packing147
  - Outer Chamber Packing147
  - Packing Inside the Chamber and Equipment147
- Decommissioning148
- Disposal of the Chamber in the Federal Republic of Germany148
- Disposal of the Chamber in the Member States of the EU Except for the Federal Republic of Germany149
- Disposal of the Chamber in Non-Member States of the EU150
Troubleshooting151
- General151
- Heating151
- Gas Cylinder Pressure too Low152
- Gas Concentration154
- Sterilization156
- Humidity (Chamber Without Active Humidification)156
- Humidity (Chamber with Active Humidification)156
- Controller157
- Open Door157
Technical Description158
- Factory Calibration and Adjustment158
- Over Current Protection158
- Definition of Usable Volume159
- CB Technical Data159
- Equipment and Options (Extract)161
- Accessories and Spare Parts (Extract)163
- Important Conversion Data for Non-SI Units164
- Conversion Table for Gas Inlet Pressures, Bar - Psi164
- Dimensions165
Certificates and Declarations of Conformity166
- EU Declaration of Conformity166
Product Registration168
Contamination Clearance Certificate169
- For Chambers Located Outside the USA and Canada169
- For Chambers in the USA and Canada172

Binder CB 170 - Dimensions

Table of Contents

Related product manuals