Binder CB 170 - Page 3

CB (E7) 06/2018 Page 3/174
5.6
Principle of controller entries ............................................................................................................. 49
5.7 Performance during and after power failures .................................................................................... 49
5.8 Performance when opening the door ................................................................................................ 50
6. START UP ............................................................................................................ 50
6.1 Turning on the chamber .................................................................................................................... 50
6.2 Controller settings upon start up ....................................................................................................... 51
6.3 Entering the altitude of the installation site ....................................................................................... 52
6.4 Factory settings ................................................................................................................................. 52
6.5 Equilibration time ............................................................................................................................... 53
6.6 Operating the DuoDoor™ door lock .................................................................................................. 53
6.7 Required gas supply for the chamber with O
2
control ....................................................................... 54
6.7.1 Hypoxic control range 0.2 vol.-% up to 20 vol.- % O
2
(regular) .............................................. 54
6.7.2 Alternative control range 10 vol.-% up to 95 vol.-% (option) .................................................. 54
6.7.3 Operation without O
2
control ................................................................................................... 54
6.8 Activating / deactivating CO
2
, O
2
and humidity control ..................................................................... 55
6.9 Humidity control of the Permadry™ system ...................................................................................... 56
7. SET-POINT ENTRY IN “FIXED VALUE” OPERATING MODE ........................... 57
7.1 Set-point entry through the “Setpoints” menu ................................................................................... 58
7.2 Direct setpoint entry via Normal display ............................................................................................ 59
7.3 Special controller functions via operation lines ................................................................................. 60
7.4 Safety instructions for setting high gas concentrations ..................................................................... 61
8. TIMER PROGRAM: STOPWATCH FUNCTION .................................................. 62
8.1 Starting a timer program ................................................................................................................... 62
8.1.1 Performance during program delay time ................................................................................ 62
8.2 Stopping a running timer program .................................................................................................... 63
8.2.1 Pausing a running timer program ........................................................................................... 63
8.2.2 Cancelling a running timer program ........................................................................................ 63
8.3 Performance after the end of the program ........................................................................................ 63
9. TIME PROGRAMS ............................................................................................... 64
9.1 Starting an existing time program ..................................................................................................... 64
9.1.1 Performance during program delay time ................................................................................ 65
9.2 Stopping a running time program ...................................................................................................... 65
9.2.1 Pausing a running time program ............................................................................................. 65
9.2.2 Cancelling a running time program ......................................................................................... 65
9.3 Performance after the end of the program ........................................................................................ 65
9.4 Creating a new time program ............................................................................................................ 66
9.5 Program editor: program management ............................................................................................. 66
9.5.1 Deleting a time program ......................................................................................................... 67
9.6 Section editor: section management ................................................................................................. 68
9.6.1 Add a new program section .................................................................................................... 69
9.6.2 Copy and insert or replace a program section ........................................................................ 69
9.6.3 Deleting a program section ..................................................................................................... 70
9.7 Value entry for a program section ..................................................................................................... 71
9.7.1 Section duration ...................................................................................................................... 71
9.7.2 Set-point ramp and set-point step ........................................................................................... 72
9.7.3 Special controller functions via operation lines ....................................................................... 74
9.7.4 Setpoint entry .......................................................................................................................... 75
9.7.5 Tolerance range ...................................................................................................................... 75
9.7.6 Repeating one or several sections within a time program ...................................................... 76
9.7.7 Saving the time program ......................................................................................................... 77
10. WEEK PROGRAMS ............................................................................................. 78
10.1 Starting an existing week program .................................................................................................... 78
10.2 Cancelling a running week program ................................................................................................. 78
10.3 Creating a new week program .......................................................................................................... 79